Category: STARTER KITS, PROGRAMMERS, MODULES

Evaluation kit with an i.MX 8M Nano quad-core processor, 2GB DDR4 RAM and 16GB eMMC 5.0/5.1 memory. Equipped with 802.11a/b/g/n/ac Wi-Fi module and BT4.1, MIPI-CSI and MIPI-DSI connector, audio Jack 3.5 mm, USB 3.0 and Ethernet. NXP NXP8MNANOD4-EVK

Module with 6-axis IMU LSM6DSO sensor, which combines a 3-axis accelerometer and gyroscope, as well as a 9kB FIFO buffer and event handling functions. Communicates via I2C or SPI. SparkFun SEN-18020

Isolated UART-RS485 converter designed for M5Stack sets. It allows communication within an industrial serial interface. M5Stack U094

Air530Z GPS module with external antenna. The board is equipped with a Grove connector and communicates via the UART interface. Seeed Studio 109020022

A Thing Plus development board that combines the Matter protocol and the Qwiic SparkFun ecosystem to facilitate the prototyping of IoT devices. It uses the MGM240P module from Silicon Labs, which provides secure connectivity for both 802.15.4 with Mesh (Thread) and Bluetooth® Low Energy 5.3 protocols. SparkFun DEV-20270

Module with MOSFET transistor, 5-36 V, 20 A, switching frequency 1 kHz. DFRobot DFR0457

Laser dust sensor is a digital universal particle concentration sensor,it can be used to obtain the number of suspended particulate matter in a unit volume of air within 0.3 to 10 microns, namely the concentration of particulate matter, and output with digital interface, also can output quality data of per particle. DFRobot SEN0177

M.2 module that allows the Edge TPU coprocessor to be used in existing systems. It allows you to make modern mobile vision models in a power efficient manner. Coral M.2 Accelerator A+E key G650-04527-01

Board with WiFi and Bluetooth Espressif ESP32-C3 module. It offers 4MB Flash and 400KB SRAM and a LiPo charging circuit. The set includes an expansion board with a display connector. DFRobot DFR0868

This ESP8266-based development board is designed for rapid IoT application development. It features support for two Grove Plug-n-Play connectors, digital and analog I/O, and UART and I2C interfaces for connecting multiple sensors and modules. The device supports OTA firmware updates, a RESTful API, and integration with mobile apps and IFTTT, allowing for easy remote control and monitoring. Seeed Studio 102110057

Development kit with ESP32 WiFi and Bluetooth module and 0.96 "OLED display. It has a built-in Li-Pol charger module and a USB-UART converter function. ModOLEDESP32_V2.0_TTGO

Module with SPDT switch. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020004

RS485 converter designed for sets from the M5ATOM series. It allows you to connect to development kits devices controlled by the RS485 bus. M5Stack T002

Gravity: Analog Sound Sensor is a sound sensor with Gravity analogue output. The module can be supplied with 3.3 ... 5V voltage. DFRobot DFR0034

Module with WiFi and BLE Espressif ESP32-S3 system and LCD TFT display. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5483

Expansion module for Seeeduino XIAO. It is equipped with an OLED display, RTC, MiniSD slot, buzzer, buttons, servo connector and numerous interfaces. Seeed Studio 103030356

Universal EEPROM and Flash (I2C and SPI) serial memory programmer. It is controlled from the computer via the USB interface and software for Windows systems. EZP2019

Board with RP2040 microcontroller and HDMI video connector. Has a built-in LiPo charging circuit and STEMMA QT connector. Allows the use of the Feather module to display data on a monitor. Adafruit 5710

Module with EEPROM memory, capacity 512 kbit (64kB). Communication takes place via the I2C interface. The module has 3 jumpers that enable selection of one of 8 addresses. SparkFun SPX-14764

The STEVAL-STLKT01V1 is a comprehensive development kit designed to support and expand the capabilities of the SensorTile and comes with a set of cradle boards enabling hardware scalability