Category: STARTER KITS, PROGRAMMERS, MODULES

A compact IoT device that combines an ESP32S3 processor with a Wio-SX1262 LoRa module, enabling communication distances of up to 5 km in the 868–915 MHz band. With support for LoRaWAN, 2.4 GHz Wi-Fi, Bluetooth 5.0, and expansion options for GNSS and sensors, it is a versatile solution for IoT gateways and nodes. Seeed Studio 102010611

The KAmod BlackPill 411 is an evaluation board featuring the STM32F411CEU microcontroller, offering versatile programming capabilities with a USB-C connector and a pre-installed bootloader compatible with Arduino IDE. Equipped with 32 GPIOs, a modified power circuit, and ESD protection, it is perfect for embedded projects.

KA-NUCLEO-F411CE v2 is a development board based on the STM32F411CE microcontroller. It has a built-in programmer compatible with ST-Link / v2-1, it is possible to program and debug the microcontroller via the USB connector.

Board with WiFi and BLE Espressif ESP32-S3 module and OV3660 camera and digital microphone. It offers 8 MB Flash memory and 8 MB SRAM. It is equipped with a USB type C connector and a WiFi/BT antenna. Seeed Studio 113991115

Evaluation board with an ESP32-WROOM-32U Wi-Fi module featuring a U.FL antenna connector, RS485 interface, and a high-performance power supply

The KAmodRS module is a reliable RS232-UART converter supporting voltages from 3 V to 5.5 V and enabling data transmission at a speed of up to 250 kbit/s. Thanks to the use of the MAX3232 chip, the module is ideal for a wide range of electronic and microcontroller applications requiring stable and effective serial communication

3-axis motion sensor module with digital output

A small development kit with a SAMD21 ARM Cortex M0 + microcontroller. There are 14 GPIO connectors on the board, including 11 digital and analog pins, 10 PWM, DAC, I2C, UART, SPI, SWD. Compatible with Arduino. Seeed Studio 102010328

KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.

Espressif ESP32-S3 WiFi and BLE module board. It offers 8 MB of flash memory and 8 MB of SRAM. It is equipped with a USB type C connector and a WiFi/BT antenna. Seeed Studio 113991114

Module with 8 LEDs

Vertical Grove socket for through-hole mounting, 4-pin, pitch 2.0 mm. Set of 10 pieces. Seeed Studio 110990030

9-axis expansion module with motion sensors. The module combines two integrated circuits: FXAS21002C 3-axis gyroscope and FXOS8700CQ 6-axis accelerometer/magnetometer. The board is equipped with connectors compatible with Arduino R3. NXP FRDM-STBC-AGM01

The cable that outputs the ATMEL ICE programmer signals without insulated terminals

Angled Grove socket for through-hole mounting, 4-pin, pitch 2.0 mm. Set of 10 pieces. Seeed Studio 110990037

The KAmod BlackPill 401 is an evaluation board with an STM32F401CCU microcontroller, featuring USB-C with ESD protection and a modified power circuit. With a pre-installed bootloader, it supports Arduino IDE, offering 32 GPIOs and versatile programming capabilities

Espressif ESP32 is an integrated circuit that combines Wi-Fi functionality and Bluetooth 4.0 BLE. Integrated 32-bit, dual-core Xtensa LX6 processor, 448kB ROM, 520kB SRAM. ESP32 allows you to work with many interfaces, including SPI, I2C, UART, CAN, ETH, IR and can be powered by 2.2V-3.6V. The system has a housing QFN48 (6x6mm). ESP32 Chip

KAmodL3GD20 is a digital gyroscope module with L3GD20 chip. It makes possible to measure angular velocity up to ± 2000 degrees per second. It has a embedded voltage regulator and level translators on SDA/SCL lines, thanks to which it can be used in systems supplied with a voltage of 2.5 V-5.5 V. KAmodL3GD20

Compact and energy-efficient solution combining Bluetooth 5.0 and LoRa (862–930 MHz), ideal for IoT projects requiring long range and low power consumption. It uses the XIAO nRF52840 MCU with Cortex-M4 core and support for multiple interfaces and the LoRa SX1262 module for reliable wireless communication. The kit is perfect for applications such as Meshtastic, asset tracking, sensor networks or educational projects. Seeed Studio 102010710

KAmodLSM6DS3 is a module that allows measurement of acceleration and angular velocity values. It has a built-in voltage stabilizer and level translators on SDA / SCL lines, thanks to which it can be used in 2.5-5.5V voltage systems