Set of 4 pieces, each piece is 3 rows by 4 rows. Adafruit 816

Module with 6-axis IMU sensor that allows you to measure acceleration and rotational speed in the range up to ±16g and ±2000dps. Equipped with a STEMMA QT connector, it communicates via I2C or SPI. Adafruit 4503

Module with 16-channel PCF8575 IO expander controlled by the I2C interface. Equipped with a STEMMA QT connector. Adafruit 5611

Module with 4-channel 12-bit DAC MCP4728 converter with built-in EEPROM memory. Equipped with a STEMMA QT connector, it communicates using the I2C bus. Adafruit 4470

Compact ESP32-based controller for addressable LEDs, designed for projects using WLED. Power is supplied via USB Type-A at 5 V and up to 2 A, while two signal outputs with 5 V level shifting provide control of compatible LED lighting. The board features WiFi, Bluetooth, an I2S microphone, an infrared receiver and screw terminal blocks. Adafruit 6332

Module with an RFID tag based on the ST25DV16K chip. It can be reprogrammed via the I2C bus. Equipped with STEMMA QT connector and PCB antenna. Adafruit 4701

Module with high power IR LED transmitter. It has a built-in N-channel FET driver and can emit an IR signal with a range of up to 10 m. Adafruit 5639

MEMS accelerometer, magnetometer and gyroscope on a single die with a high speed ARM Cortex-M0 based processor

Adafruit 448 - 12V EL wire/tape inverter

A handy way to power 12V powered devices with a center-positive 2.1mm DC barrel jack from a USB port. Adafruit 2778

Electronic pencil that allows you to make music while drawing. It uses the conductive properties of pencil graphite to create a variety of sounds. Adafruit 124

4-core cable with a length of 400 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 5385

A module with a USB converter - GPIO/ADC/I2C based on the MCP2221A chip. It allows you to connect sensors, displays or PWM drivers to the computer via a 2.54 mm or Stemma QT/Qwiic connector. Adafruit 4471

4-digit 7-segment 0.56 "LED display. Built-in HT16K33 controller allowing communication via I2C bus. Equipped with STEMMA QT connector. Adafruit 5601

RGB LED driver module designed for QT Py and Xiao boards. It uses a 3.3V/5V voltage level converter and allows to control 30 Neopixel LEDs. Adafruit 5645

Module with ENS160 gas sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C or SPI interface. Adafruit 5606

The DRV5032 Hall Effect Magnetic Field Detection Module is an energy-efficient module for IoT projects, positioning systems, and battery-powered devices. With its digital output, compact design, and wide supply voltage range (1.65 to 5.5 V), it can be easily integrated into a variety of applications, offering magnet detection without the need for continuous power consumption. Adafruit 6051

Clock signal generator with a frequency of 8 kHz to 160 MHz based on the SI5351A integrated circuit. Communication with the module takes place via the I2C bus. Adafruit 5640

Cable (adapter) STEMMA QT/Qwiic for Arduino MKR (ESLOV) 100 mm long. It enables interoperability between systems based on I2C SparkFun Qwiic and Adafruit STEMMA QT and Arduino MKR boards. Adafruit 4483

Plate allowing a   connect the wires with goldpins to a maximum of 50- conductor , 0.5 mm FPC tape . Adafruit 1492