Development board in Feather format equipped with AW-CU488. The module has an integrated WiFi wireless communication controller, LiPo charging circuit and Qwiic connector. SparkFun DEV-19957

HDMI-USB adapter dedicated to video capture and transfer to devices with USB type A connector. Waveshare HDMI to USB Adapter

Module with GNSS MAX-M10S receiver. It can receive signals from GPS, GLONASS, BeiDou and Galileo constellations. It has an SMA connector for connecting an external antenna and a Qwiic socket. SparkFun GPS-18037

The S9V11F3S5CMA switching step-up/step-down regulator efficiently produces a fixed 3.3 V (default) or 5 V (selectable) output whether it is higher or lower than the input voltage, which can range from 2 V to 16 V. (Note: minimum start-up voltage is 3 V, but it operates to 2 V after that.)

Function module designed for MicroMod boards. Equipped with the ZED-F9P GNSS receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It communicates via UART, I2C and SPI interfaces. SparkFun GPS-18378

Function module designed for MicroMod boards. Equipped with GPS with NEO-M9N 92-channel GNSS receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It communicates via UART, I2C and SPI interfaces. SparkFun GPS-18378

Module with 9-axis IMU. It combines the ISM330DHCX (accelerometer and gyroscope) and MMC5983MA (magnetometer) systems. Communication via the I2C interface. SparkFun SEN-19895

Pololu Dual G2 High-Power Motor Driver 18v22 is an extension that allows you to control two DC motors designed for Raspberry Pi. The motors can be powered with 6.5-30V and draw up a maximum current of 22A. Pololu 3754

Pololu Dual G2 High-Power Motor Driver 24v18 is an extension that allows you to control two DC motors designed for Raspberry Pi. The motors can be supplied with 6.5-36V voltage and can draw a maximum current of 18A. Pololu 3756

8-segment display module, 4 digits with commas

Card with RFID tag for systems operating at 125 KHz. Provides the ability to read and write the ID number

Female terminal block, 10-pin. Pitch 3.5mm. Height 15.6mm. KF2EDGK

The USB to 2.5G Ethernet converter is a compact and efficient tool that extends network functionality to devices lacking an RJ45 interface. With broad system compatibility and driverless operation, it is well-suited for mobile setups, single-board computers, embedded systems, and upgrading older hardware to higher network speeds.

Color e-Paper display 4" with E Ink Spectra 6 technology offers high image quality with minimal power consumption. Intended for use in dynamic information systems, electronic labels, and integration with microcontrollers and single-board computers. Requires an external controller module supporting the SPI interface.

Shielded RJ45 connector with integrated magnetics (PulseJack – GigJack T12) designed for 10/100/1000Base-T applications. The JK0-0036NL integrates the Ethernet connector and isolation transformers into a single package, simplifying PCB design while ensuring stable data transmission and galvanic isolation in networking and industrial devices. Pulse Electronics JK0-0036NL

8 MPx camera module with IMX219 sensor and wide-angle lens. To be used as a replacement on the RPI Camera Board V2. Waveshare IMX219-D160

LM35 analog temperature sensor module for Arduino. DFRobot DFR0023

Driver for e-Paper displays in the form of an overlay for Arduino and Nucleo. The SPI interface is used for communication with the controller. Waveshare e-Paper Shield

16-bit Microcontroller, Ultra Low Pwr, 16MHz, Comparator, 1kB Flash, 128b RAM, TI, TSSOP14, RoHS