Water atomizer - Grove module
ID: 564199
5906623414123
zł64.50
Tax included
zł52.44 tax excl.
The kit includes a control module (with ETA1617 and NE555) and an ultrasonic transducer. The water atomiser module allows for the construction of, for example, a small humidifier. The module has a connector in accordance with the Grove standard. Seeed studio 101020090
Description
The kit includes a control module (with ETA1617 and NE555) and an ultrasonic transducer. The water atomiser module allows for the construction of, for example, a small humidifier. It can also be used for other projects where atomization (spraying) is needed. The module has a connector in accordance with the Grove standard.
The module can be used with the Base Shield V2 - shield extension with Grove connectors for Arduino
Attention!
Do not touch the contacts to which the ultrasound transducer is connected (marked with a red frame in the picture above) because the voltage (momentary) up to 65 V may occur on them, in addition the area heats up during operation.
Do not touch the contacts to which the ultrasound transducer is connected (marked with a red frame in the picture above) because the voltage (momentary) up to 65 V may occur on them, in addition the area heats up during operation.
properties
- Based on the following systems: ETA1617, NE555
- Maximum power: 2 W
- Peak output voltage: 65 ± 5 V
- Operating frequency: 105 ± 5 kHz
- Grove connector
- Power supply: 5 V
Included
- Water atomizer - Grove module
- Ultrasonic transducer
- Grove system cable
564199
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A small module with a temperature sensor (thermistor). As the temperature changes, the resistance of the thermistor changes, which allows the temperature to be measured in the range from -40 to 125 ° C with an accuracy of 1.5 ° C. The module has a connector in accordance with the Grove standard. Seeed studio 101020015
zł15.36
24h
Available quantity: 2
Available
Module with a flame sensor or other light sources with a wavelength in the range of 760 to 1100 nm. It was based on the YG1006 sensor (photovolver NPN). The sensor has a connector compatible with the Grove standard. Seeed studio 101020049
zł38.14
24h
Available quantity: 2
Available
The module allows the detection of volatile organic compounds (VOC) in the air, based on Winsen\'s WSP2110 system. Allows for detection in the air; formaldehyde (HCHO), methane, benzene, toluene, alcohol, etc. The sensor output is an analog signal. Seeed studio 101020001
zł79.32
24h
Available quantity: 4
Available
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
zł24.40
24h
Available quantity: 19
Available
Other products in the same category (16)
RS232 module used as a communication extension equipped with a female DSUB9 connector, allowing easy connection to a PC or USB-RS232 adapter. Segger emPower RS232 Add-On (6.32.32)
zł95.87
1 weeks
No product available!
J-Link 6-pin Needle Adapter (8.06.16)
zł544.74
24h
Available quantity: 5
Available
The ESP32 WiFi and Bluetooth module has a dual-core 32-bit MCU that integrates WiFi HT40 and Bluetooth / BLE 4.2 technology. Designed for mobile devices and Internet of Things (IoT) applications. DFRobot TEL0111
zł38.93
24h
Available quantity: 3
Available
Switch module with an interlock. DFRobot DFR0423
zł9.02
24h
Available quantity: 5
Available
Advanced development suite designed for creating embedded applications for Cortex-A and Cortex-R processors. Includes a full Embedded Studio development environment, J-Link PLUS hardware debugger, and a set of tools such as embOS (RTOS), emWin PRO (GUI), emNet PRO (TCP/IP), emFile PRO (file system), and emUSB-Device/Host PRO (USB support). Segger Embedded Studio PRO - Cortex-A/R edition (20.50.08)
zł94,094.78
1 weeks
No product available!
No product available!
Flash Programmer for ARM7/9/11, Cortex, RX and PPC cores
zł5,109.12
24h
Available quantity: 1
Available
Air quality sensor module based on the ENS160 system. It communicates via the I2C interface (Gravity connector). DFRobot SEN0514
zł97.10
24h
Available quantity: 2
Available
A sensor that detects the oxygen concentration. Equipped with a factory calibrated probe. It communicates via the UART interface or the analog output. Seeed Studio 101020912
zł539.04
4 weeks
No product available!
Available
The X-NUCLEO-GNSS1A1 expansion board is based on the Teseo-LIV3F tiny GNSS module
zł213.00
24h
Available quantity: 2
Available
SparkFun weather: bit module designed for micro: bit, with temperature, humidity and pressure sensor (BME280 system). In combination with the micro: bit module, it is possible to build a fully functional weather station. SparkFun DEV-15837
zł123.04
24h
Available quantity: 1
Available
Module with a slide potentiometer. Depending on the position of the slider, the resistance value (maximum resistance 10kΩ) changes, which translates into the voltage value at the analog output of the module. The module has a connector in accordance with the Grove standard. Seeed studio 101020036
zł32.04
24h
Available quantity: 1
Available
Starter kit with a microcontroller from the Kinetis KL46Z family (Cortex-M0 +), integrated with the OpenSDA programmer-debugger, capacitive touch slider, LED, MEMS 3D accelerometer and 4-digit LCD. NXP FRDM-KL46Z
zł269.84
24h
Available quantity: 4
Available
A module that enables precise switching of Flasher signals in production environments, preventing interference between test devices connected to the same lines. By controlling relays via VTSUPPLY, it ensures stable and reliable operation in testing and programming processes. Segger Relay Adapter (8.06.41)
zł1,036.19
1 weeks
No product available!
STM32 Nucleo-144 development board with STM32F446ZET6 MCU, supports Arduino, ST Zio and Morpho
zł90.50
24h
Available quantity: 2
Available
The kit includes a control module (with ETA1617 and NE555) and an ultrasonic transducer. The water atomiser module allows for the construction of, for example, a small humidifier. The module has a connector in accordance with the Grove standard. Seeed studio 101020090