Gravity: Analog Carbon Monoxide Sensor (MQ7) - module with a carbon monoxide sensor
ID: 581623
5906623481194
zł46.83
Tax included
zł38.07 tax excl.
Module with an analog MQ7 carbon monoxide sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0132
Description
Module with an analog MQ7 carbon monoxide sensor. Carbon monoxide (most often called carbon monoxide) is a gas that is colorless, odorless, tasteless and extremely poisonous. Due to these properties, carbon monoxide is difficult to detect without a specialized device. With the help of the module with the MQ7 sensor, it is possible to build a detector that will detect CO in our environment. The module is powered with 5 V and has an analog output (Gravity connector) proportional to the measured concentration. The sensor is characterized by high sensitivity adjustable with a potentiometer and can measure the concentration of CO in the range from 20 to 2000 ppm. The Wiki page contains the manual and sample programs.
Features
- Measurement range: from 20 to 2000 ppm
- Analog interface
- Quick reaction
- Adjustable sensitivity by potentiometer
- Stable performance
- Simple connection via the Gravity connector
- Power supply: 5V
- Size: 40 x 20mm
581623
Data sheet
- Interface
- Sygnał analogowy
- Type of sensor
- MQ-7
- Power supply voltage
- 5 V
- Concentration measurement
- CO
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.42
Delivery date unknown
No product available!
Available
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł21.65
24h
Available quantity: 1
Available
Set of 10 cables, 30 cm long, for analog sensors compatible with the Gravity standard. DFRobot FIT0031
zł22.18
24h
Available quantity: 2
Available
Other products in the same category (16)
Sensor that detects the concentration of chlorine. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0468
zł722.94
4 weeks
No product available!
Adapter for MQ gas sensor with potentiometer for analog signal calibration. MOD 72
zł13.03
24h
Available quantity: 5
Available
The MQ-3 sensor allows you to measure the concentration of alcohol vapors. The measuring range of the sensor is in the range of 0.05 mg / L to 10mg / L, and an analogue signal is obtained at the output.
zł8.44
24h
Available quantity: 11
Available
Module with ammonia sensor made in MEMS technology. It allows gas detection in the range of 1 to 300 ppm and has an analog output. DFRobot SEN0567
zł40.93
24h
Available quantity: 2
Available
ENS160 gas sensor module to measure the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via an I2C or SPI interface. SparkFun SEN-20844
zł119.84
24h
Available quantity: 3
Available
Air quality sensor module based on the SGP40 system. It uses CMOSens® technology by Sensirion and provides information on air quality. Waveshare SGP40 VOC Sensor
zł67.37
4 weeks
No product available!
MQ-135 Gas Sensor
zł24.14
24h
Available quantity: 6
Available
Module with CO2, temperature and humidity sensor SCD-41. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5190
zł486.45
24h
Available quantity: 1
Available
Module with an ambient oxygen concentration sensor. The system allows you to measure the oxygen volume in the range up to 25% with a resolution of 0.15%. The module communicates via the I2C interface. DFRobot SEN0322
zł371.12
24h
Available quantity: 1
Available
Module with a VOC sensor (volatile organic compounds) made in MEMS technology. It allows gas detection in the range of 5 to 500 ppm and has an analog output. DFRobot SEN0566
zł23.94
24h
Available quantity: 2
Available
Module with the MQ3 analog alcohol sensor. It allows you to detect gas and build a simple breathalyzer. The module is powered by 5 V and has an analog output
zł14.62
24h
Available quantity: 13
Available
Module with a knock-on sensor for measurement of methane, propane and carbon monoxide (MQ-9) concentrations. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
zł10.00
24h
Available quantity: 4
Available
Module with the MiCS-5524 analog gas sensor. It allows you to measure the concentration of CO, CH4, 2H5OH, C3H8, C4H10, H2, H2S and NH3. DFRobot SEN0440
zł46.21
24h
Available quantity: 3
Available
The SCD-40 CO2, temperature and humidity sensor module provides high accuracy readings. It is equipped with a Qwiic connector and communicates via an I2C interface. SparkFun SEN-22395
zł484.35
24h
Available quantity: 1
Available
Air quality sensor module based on the SGP40 system. The board is equipped with Qwiic connectors. SparkFun SEN-18345
zł95.23
24h
Available quantity: 2
Available
Formaldehyde sensor (HCHO) dedicated to measuring ambient air quality. It is used to detect whether the surrounding environment exceeds a set concentration threshold. It is powered by a voltage of 5 V to 24 V and has an output in the form of a two-state digital signal. DFRobot SEN0595
zł106.84
24h
Available quantity: 1
Available
Module with an analog MQ7 carbon monoxide sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0132