![PS01 - Pulse sensor PS01 - Pulse sensor](https://kamami.pl/19117-large_default/ps01-optoelectronic-pulse-sensor-module.jpg)
![PS01 - Pulse sensor PS01 - Pulse sensor](https://kamami.pl/19117-large_default/ps01-optoelectronic-pulse-sensor-module.jpg)
zł12.14 tax excl.
The sensor responds to chakra changes in the tissues by analyzing the reflected light (the module contains an illuminator and a sensor).
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
The optoelectronic pulse sensor module - allows you to detect the heartbeat by analyzing the change in parameters of illuminated tissues. The module uses an amplifier and noise eliminator, thanks to which the module is precise and reliable.
Evaluation board with built-in AD8232 heart monitor module and components placed in a way allowing effective implementation of medical and fitness applications, configuration of 2 or 3 electrodes
No product available!
Heart rate measurement module compatible with Arduino and Raspberry Pi (Gravity: Heart Rate Monitor Sensor For Arduino). It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. DFRobot SEN0203
The MyoWare Power Shield is designed to take two standard CR2032 coin cell batteries to power the MyoWare Muscle Sensor. We have made this board in a way that the coin cell batteries are connected in parallel for extended capacity at a nominal 3.0V. DEV-13684
Module with pulse and SpO2 level sensor (oxygen saturation level). The module is based on the MAX30102 chip and communicates via the I2C interface.
No product available!
Module with GSR skin resistance sensor. It is used to measure skin activity, which reflects the stress response and experienced emotions. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020052
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip and communicates via the I2C or UART interface (Gravity connector). DFRobot SEN0518
The module with a heart rate sensor and the SpO2 level dedicated to micro:bit. It is based on the MAX30102 chip and communicates via the I2C interface. SparkFun SEN-15271
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240
Module with heart rate and SpO2 sensor (oxygen saturation level) MAX30100 designed for M5Stack sets. M5Stack U029
Module with an EMG signal detector. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020058
Evaluation board with built-in AD8232 heart monitor module and components placed in a way allowing effective implementation of medical and fitness applications, configuration of 2 or 3 electrodes
No product available!
Heart rate monitor module based on the popular MAX30101 and MAX32664. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-15219
Designed to pair with the MyoWare Muscle Sensor; 10-segment bar graph shows the magnitude of the measured signal. The more muscle activation measured, the higher up the board the lit LEDs will go. DEV-13688
Disposable biomedical electrodes that allow you to perform experimental ECG measurements. DFRobot FIT0510
Module with heart rate sensor, SpO2 (oxygen saturation) and smoke levels. It is based on the MAX30101 chip and communicates via the I2C interface. Pimoroni PIM438
The module with the MAX30100 chip that monitors the oxygen content in the blood and the heart rate. It consists of two LED diodes, a photodetector, optimized optics and low noise analog signal processing. modMAX30100
The sensor responds to chakra changes in the tissues by analyzing the reflected light (the module contains an illuminator and a sensor).