DC Micro motor module with metal gear with a gear ratio of 75:1. The motor is connected to the board containing the driver, so the motor can be controlled via the Gravity connector directly by the microcontroller (no additional H-bridge required). The set is controlled by the PWM signal, analogically to the servo. The module is characterized by low current consumption (less than 1 mA in the absence of a control signal). The user manual with a sample program is available on the product Wiki page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Board with ATmega2560 microcontroller (256 kB Flash, 8 kB RAM, 4 kB EEPROM) clocked at 16 MHz. USB-UART converter based on the ATmega16u2 chip. The user has at his disposal, among others: 54 I/O lines, 14 PWM channels, 16 analog inputs.
No product available!
Board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface
Extension board for Arduino Nano and Uno, 14 GPIO lines, connectors with I2C and UART interface lines. The board also has a RESET button and a voltage stabilizer
DC Micro motor module with metal gear with a gear ratio of 30:1. The motor is connected to the board containing the driver. DFRobot DFR0399
DC Micro motor module with metal gear with a gear ratio of 50:1. The motor is connected to the board containing the driver. DFRobot DFR0429
Module with the ATMega4809 microcontroller from the AVR family (48 KB Flash, 6 KB SRAM, 256 B EEPROM). The module has two 15-pin connectors equipped with GPIO, SPI, I2C, PWM, USART, DAC and ADC. Arduino ABX00028
No product available!
Board with nRF52840 microcontroller with Cortex M4F core (64 MHz, 1 MB Flash, 256 kB RAM). Equipped with BT 5.0 and IMU LSM9DS1 module. Module with headers. Arduino ABX00034
Small metal gear motor, 30 RPM speed, 3V operating voltage. GA12-N20-0001
15:1 Micro Metal Gearmotor. Pololu 4784
Small motor with metal gear and encoder, rotation speed 100 RPM, operating voltage 6 V. GA46-N20E-0045
No product available!
Small metal gear motor, 100 RPM speed, 12V operating voltage. GA12-N20-0023
No product available!
30:1 Micro Metal Gearmotor HP with Extended Motor Shaft
A small, high power motor with 210: 1 metal gear, 6 V operating voltage, 0.1 A to 1.5 A power consumption, 160 RPM speed, maximum torque of 2.8 kg * cm and carbon brushes with increased durability. Pololu 3067
No product available!
75:1 Micro Metal Gearmotor HP with Extended Motor Shaft
No product available!
Small metal gear motor, rotation speed 68 RPM, operating voltage 12 V. GA1218-N20W-0039
No product available!
This gearmotor is a miniature high-power, 12 V brushed DC motor with long-life carbon brushes and a 100.37:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
Key specs at 12 V: 320 RPM and 100 mA with no load, 30 oz-in (2.2 kg-cm) and 0.8 A at stall.
A small, high power motor with a 50: 1 metal gear, 12 V operating voltage, 0.06 A to 0.75 A power consumption, 650 RPM speed, maximum torque of 0.67 kg * cm and carbon brushes with increased durability. Pololu 3039
No product available!
Small metal gear motor, 15 RPM speed, 3V operating voltage. GA12-N20-0001
No product available!
No product available!
A small motor with a metal gear ending with a shaft with M3 thread, rotation speed 300 RPM, operating voltage 6 V. GA1036-N20M-0057
No product available!
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 51.45:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
A small motor with a metal gear ending with a shaft with M3 thread, rotation speed 100 RPM, operating voltage 6 V. GA1036-N20M-0055
DC Micro motor module with metal gear with a gear ratio of 75:1. The motor is connected to the board containing the driver. DFRobot DFR0399