MiFare Classic (13.56MHz RFID/NFC) White Tag
ID: 203676
5906623402724
zł12.94
Tax included
zł10.52 tax excl.
The tag contains a NXP S50 chip and an antenna, and is passively powered by the reader/writer when placed a couple inches away. These can be read by almost any 13.56MHz RFID/NFC reader. Adafruit 360
360 - MiFare Classic (13.56MHz RFID/NFC) White Tag - 1KB
This is a blank MiFare Classic laundry tag - often used for laundry or identification but also found in other systems where a small proximity card is desired. The tag contains a NXP S50 chip and an antenna, and is passively powered by the reader/writer when placed a couple inches away
These can be read by almost any 13.56MHz RFID/NFC reader but make sure it can handle MiFare cards as there are a few other encoding standards (like FeLica) They are tested and work great with both our PN532 NFC/RFID breakout board and Adafruit NFC/RFID Shield for Arduino!
These chips can be written to & store up to 1 KB of data in writable EEPROM divided into banks, and can handle over 100,000 re-writes. You can use our PN532 NFC/RFID breakout board or Adafruit NFC/RFID Shield for Arduino to read and write data to the EEPROM inside the tag. There is also a permanent 4-byte ID burned into the chip that you can use to identify one tag from another - the ID number cannot be changed.
These can be read by almost any 13.56MHz RFID/NFC reader but make sure it can handle MiFare cards as there are a few other encoding standards (like FeLica) They are tested and work great with both our PN532 NFC/RFID breakout board and Adafruit NFC/RFID Shield for Arduino!
These chips can be written to & store up to 1 KB of data in writable EEPROM divided into banks, and can handle over 100,000 re-writes. You can use our PN532 NFC/RFID breakout board or Adafruit NFC/RFID Shield for Arduino to read and write data to the EEPROM inside the tag. There is also a permanent 4-byte ID burned into the chip that you can use to identify one tag from another - the ID number cannot be changed.
S50 chip specification:
- 1 KiloByte (8 KiloBit) non-volatile EEPROM storage
- Built in encryption engine with 48-bit key
- 4 Byte unique identifier burned into the chip
- 13.56 MHz frequency
Tag specification:
- 25.4mm diameter x 1mm / 1" diameter x 0.03"
- 0.9 grams / 0.03 oz
- Works about 2" away from reader
| Tutorials on the Adafruit Learning System featuring this product: | |
 |
Adafruit NFC/RFID on Raspberry Pi Add RFID/NFC read and write to your Pi in an hour! |
203676
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
NFC module designed for Arduino. Meets the standards of reader mode, P2P mode and card emulation mode. The board has an integrated RF antenna. NXP OM5578/PN7150ARDM
zł39.90
24h
Available quantity: 29
Available
Handheld RFID card reader enabling card duplication. It allows you to read data from one card and write it to the other
zł37.32
24h
Available quantity: 9
Available
Module with RFID reader designed to work with micro:bit. It is equipped with a buzzer and can control two modeling servos. SB Components 21291
zł115.60
24h
Available quantity: 2
Available
The X-NUCLEO-NFC02A1 is a dynamic NFC/RFID tag board based on M24LR04E-R, for expansion of STM32 Nucleo boards
zł52.15
24h
Available quantity: 2
Available
Module with RFID reader. It is equipped with a buzzer and communicates via UART or USB interface. SB Components 20669
zł75.76
4 weeks
No product available!
Intelligent RFID identifier cooperating with iNode Control Point
zł101.84
24h
Available quantity: 2
Available
Intelligent RFID identifier cooperating with iNode Control Point
zł101.84
24h
Available quantity: 1
Available
Available
RFID card with dimensions 54 mm x 85.5 mm x 0.87 mm, working on the 13.56 MHz frequency. RFID Tag Card
zł1.37
24h
Available quantity: 27
Available
The 13.56 MHz RFID reader module in a set with a keyring and RFID card
zł9.53
24h
Available quantity: 20
Available
RFID Reader/Transponder IC 13.56MHz ISO 14443 I2C, SPI, UART, -25..85C, VFQFN32, NXP
zł43.80
24h
Available quantity: 15
Available
A module with an NFC PN532 transceiver, which supports proximity communication at the frequency of 13.56 MHz. The board is equipped with a Grove connector and communicates via the I2C or UART interface. Seeed Studio 113020006
zł97.67
24h
Available quantity: 5
Available
NFC reader with USB interface. It allows you to easily read data from an NFC/RFID card using a computer. JT308
zł20.14
24h
Available quantity: 13
Available
FSC-BP108 iBeacon is a durable and energy-efficient Bluetooth 5.1 tag with IP67 protection, supporting popular beacon formats and enabling remote configuration via a mobile app. It is suitable for localization systems, asset tracking, and proximity-based marketing.
zł102.93
24h
Available quantity: 6
Available
KAmodNFC is an expansion board with M24LR64E-R chip – dynamic tag with 64kb EEPROM memory and dual communication interface (I2C/RF). On board is placed also signalization of energy harvesting function, which is in M24LR64E-R chip embedded.
zł28.91
24h
Available quantity: 210
Available
A small key ring with an RFID tag for systems operating at 125 KHz. Provides the ability to read and write a unique ID number
zł2.83
24h
Available quantity: 37
Available
The tag contains a NXP S50 chip and an antenna, and is passively powered by the reader/writer when placed a couple inches away. These can be read by almost any 13.56MHz RFID/NFC reader. Adafruit 360