

zł77,234.96 tax excl.
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 800 MHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. Micsig MOIP800P
An isolated fiber optic probe that works in the frequency band up to 800 MHz. It uses a standard BNC interface and can be connected to an oscilloscope or multimeter. Utilizing SigOFIT optical isolation technology, it offers high accuracy and excellent suppression of oscillations caused by high-frequency common-mode noise.
The probe has excellent amplitude-frequency characteristics and the DC gain accuracy is less than 1%. The maximum noise floor in this range is 1.41 mVrms and the zero drift is less than 500 μV. It is an excellent choice for the study of third generation semiconductors and devices based on SiC and GaN. The probe test leads are short and have an input capacitance of less than 3 pF when transmitted via coaxial cable, allowing for very safe testing.
Unlike traditional differential probes that can only test high-voltage signals, the SigOFIT can be used with a variety of tips to test differential mode signals from ±1.25 V to ±2500 V, achieving full output range and very high signal to ratio noise. It will be used in industry, automotive electronics, when servicing power supplies and inverters. It is dedicated to Micsig devices.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Test probe tip with 20X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP20-1G
No product available!
Test probe tip with 50X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP50-1G
No product available!
Test probe tip with 1000X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP1000-1G
No product available!
Test probe tip with 2000X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP2000-1G
No product available!
Oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Hantek HT25COP
A probe tip with attenuation factor of 10000X. Dedicated to Micsig probes from the SigOFIT series operating in the 500 MHz frequency band. Micsig OP10000-5
No product available!
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-2.3mm
No product available!
Micsig MDP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 500 MHz and the ability to measure voltage up to 1500 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig MDP1505
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-1.5mm
No product available!
Oscilloscope probe with BNC plug with 100MHz bandwidth. Uni-T UT-P04
The PP80B oscilloscope probe is a reliable tool for precise measurements, compatible with digital and analog oscilloscopes, offering a bandwidth of up to 80 MHz and the ability to select the attenuation factor. Hantek PP-80B
BNC connector cable (adapter) to the "Alligator clip" connector. It allows you to conveniently connect the device, e.g. to an oscilloscope. Digilent (240-134)
Probe for measuring direct and alternating current up to 100 A. It works in the 800 kHz band, it can be connected to the oscilloscope through the BNC connector. Powered by USB. Micsig CP2100A
High-voltage differential probe. It has good measurement characteristics: a bandwidth of 50 MHz and an operating voltage of up to 1300 V. The probe has two attenuation coefficients: 50X and 500X. Hantek HT8050
Micsig DP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 200 MHz and the ability to measure voltage up to 3000 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP3002
A set of needle probes used for piercing wire insulation. They can be used as pin probes when working with small PCBs or connectors. Hantek HT307
No product available!
Universal oscilloscope probe with BNC connector. It has a voltage divider of 10:1 and offers a frequency response of 100 MHz. It allows measurements with a maximum voltage of up to 600 V. P6100
Probe for measuring AC currents up to 1000 A. It works in the range from 10 Hz to 100 kHz, it can be connected to the oscilloscope through the BNC connector. Micsig ACP1000
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 200 MHz, it can be connected to the oscilloscope via the BNC connector. Micsig MOIP200P
No product available!
Test probe tip with 20X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 350 MHz and 500 MHz frequency bands. Micsig OP20-5
No product available!
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 800 MHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. Micsig MOIP800P