Category: STARTER KITS, PROGRAMMERS, MODULES

A sensor that detects the concentration of hydrogen. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0473

A sensor that detects the concentration of hydrogen chloride. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0474

A sensor that detects the concentration of phosphine. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0476

A sensor that detects the concentration of carbon monoxide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0466

A sensor that detects the oxygen concentration. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0465

Development board containing the STM32H743XI microcontroller, 5MP OV5640 camera module, FLIR Lepton socket and the VL53L0X laser rangefinder. Also equipped with a 4.3 "LCD display. SparkFun DEV-18482

A sensor that detects the oxygen concentration. Equipped with a factory calibrated probe. It communicates via the UART interface or the analog output. Seeed Studio 101020912

Module with a sensor of formaldehyde (methanal) concentration in the air. The board is equipped with a Grove connector and communicates via the I2C or UART interface. Seeed Studio 101020972

Module with the SLA-05VDC-SL-C relay with a maximum load of 30 A. The board is equipped with a Grove connector and is controlled by a digital signal. Seeed Studio 103020012

Acrylic housing designed for Seeeduino XIAO Expansion Board modules. Provides good protection against damage and has a dedicated space for the battery. Seeed Studio 110010024

Module with RGB LED diode. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 104020048

Module with a 3-axis magnetometer BMM150. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020492

The X-NUCLEO-S2868A1 expansion board is based on the S2-LP radio and operates in the 868 MHz ISM frequency band. The expansion board is compatible with ST morpho and Arduino UNO R3 connectors

The SparkFun micro:climate kit is a full weather station kit that is built on top of the weather:bit carrier board. The set contains all the elements needed to build a weather station. Sparkfun KIT-16274

The set consists of STM32 Nucleo NUCLEO-G431RB plate with STM32G431RB microcontroller, X-NUCLEO-IHM16M1 plate with three-phase STPIN830 BLDC / PMSM motor controller and GBM2804H-100T motor. STMicroelectronics P-NUCLEO-IHM03

NUCLEO series starter kit equipped with STM32G474RE microcontroller (512 kB Flash, Cortex-M4), with built-in programmer-debugger ST-Link-V3E, equipped with connectors compatible with Arduino.

The XTS-FMC module is an extension for FPGA devices that allows access to communication channels via the SMA connector. P0401

Development board with SAMD21 microcontroller (ARM Cortex® M0+), 22 I/O lines, 12 PWM channels, micro-USB. The module has a built-in SD connector with dedicated SPI (SPI1) interfaces that allow you to play music files. Arduino MKR Zero ABX00012

Development board with ST Zio and ST morpho connectors, based on the STM32H755ZI microcontroller. Thanks to the embedded STLINK-V3 programmer, it is possible to program and debug the microcontroller via USB. STMicroelectronics NUCLEO-H755ZI-Q

Development board with ST Zio and ST morpho connectors, based on the STM32H753ZI microcontroller. Thanks to the embedded STLINK-V3 programmer, it is possible to program and debug the microcontroller via USB. STMicroelectronics NUCLEO-H753ZI