Category: STARTER KITS, PROGRAMMERS, MODULES

Function module designed for MicroMod boards. Allows CAN network communication to be added to the design. SparkFun SPX-21775

An expansion board designed for FireBeetle M0 and ESP32-E kits. The board has 12 GPIO pins, 5 ADC, UART, I2C and SPI interfaces. The pins are color coded according to the Gravity standard. DFRobot DFR0762

Module with proximity and ambient light sensor based on the VCNL4020 system. It allows you to detect obstacles in the range from 0 to 20 cm and measure light intensity from 0.26 to 16,000 lux. It communicates via the I2C bus. Adafruit 5810

A miniature board with dimensions of 20x22 mm with an ATmega32U4 microcontroller. Compatible with Arduino Leonardo. DFRobot DFR0816

Gravity: Vibration Motor Module is a module with a small vibration motor powered by 5V voltage, controlled by a binary signal (high / low state) or using a PWM signal. DFRobot DFR0440

Gamepad module with joystick and buttons designed for micro:bit development kit. Its shape and design resemble that of a portable game controller. DFRobot DFR0536

Gravity: Digital Crash sensor is a microswitch module (left) often called a limit switch. The module is powered by 5V voltage and has a digital two-state output. DFRobot SEN0138-L

The board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 16 MB of QSPI flash memory. The system can be programmed in C/C++ or microPython. SparkFun DEV-17745

Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 5A. DFRobot SEN0287

Evaluation board with ATSAMD21E18 microcontroller (Cortex M0 +, 48 MHz, 256 KB Flash and 32 KB RAM). Equipped with a STEMMA QT connector. Adafruit 4600

The module with the MCP96L01 amplifier designed to work with a thermocouple type K, J, T, N, S, E, B, or R. It has a screw connection for connecting a thermocouple and communicates via I2C. Adafruit 5165

Beetle ESP32 is a small (35 × 34mm) board thanks to which the creation of the Internet of Things (IoT) is very simple. The module was based on the ESP32 system, which allows for Bluetooth communication (compatible with Bluetooth 4.2) and WiFi. DFRrobot DFR0575

An evaluation kit dedicated to Internet of Things (IoT) applications that supports Wi-Fi, Sub-GHz 868 MHz, Bluetooth and NFC communication protocols. STMicroelectronics STEVAL-IDI004V2

Soil moisture sensor dedicated to micro:bit. It is supplied with the voltage from 3.3 V to 5 V and communicates via an analog signal. SparkFun SEN-15272

Waterproof soil moisture sensor with analog output. The probe has a pointed tip, which allows it to be easily inserted into the ground. It is supplied with the voltage from 3.3V to 5.5V. DFRobot SEN0308

Module with integrated BME688 gas, pressure, temperature and humidity sensor placed in one MEMS housing. It is equipped with an I2C interface. Adafruit 5046

Hub with Qwiic connectors that allows you to connect several boards to the evaluation kit. There is no built-in control system, but only splits one connector into 3 more. SparkFun BOB-18012

Set with the ADC HX711 transducer module and a pressure sensor in the form of a tensometric beam. It communicates via the UART interface. It allows you to build a simple home scale. DFRobot SEN0160

Module with 12-channel MPR121 capacitive touch sensor. The board is equipped with a Stemma QT connector and communicates via the I2C interface. Adafruit 4830

NUCLEO-WBA55CG is a low-power STM32 development board with Bluetooth LE, Thread, and Zigbee support, designed for IoT projects. ST morpho and ARDUINO Uno V3 connectors enable flexible expansion and rapid prototyping.