Category: STARTER KITS, PROGRAMMERS, MODULES

Module with red LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0021-R

Photon Micro OLED Shield breaks out a small monochrome, blue-on-black OLED to use with your Photon module. It’s “micro”, but it still packs a punch – the OLED display is crisp, and you can fit a deceivingly large amount of graphics on there. DEV-13628

A small module with a PIR motion sensor. It allows detecting movement within a maximum range of 6 meters (default up to 3 meters). The measuring angle is 120 degrees. The module has a connector in accordance with the Grove standard. Seeed Studio 101020020

The module with the tilt sensor, the sensor output is a digital signal. The module has a connector in accordance with the Grove standard. Seeed studio 101020025

Module with L3G4200D (3-axis gyroscope with digital output)

Pin expander designed for Feather plates. It is equipped with three sets of female strips and holes for prototyping. Adafruit 3417

Mini6245 Processor card

K8048 is a prototyping kit and PIC programmer, enabling testing and programming of various Microchip microcontrollers. Thanks to its extended functions and RS232 support, it is suitable for education, prototyping, and hobby electronic projects.

The touch sensor module (touch button) can be used as a replacement for traditional mechanical buttons. It operates based on the TTP223-B system, which measures the capacity of the metal field on the module. The module has a connector in accordance with the Grove standard. Seeed studio 101020037

Module with a flame sensor or other light sources with a wavelength in the range of 760 to 1100 nm. It was based on the YG1006 sensor (photovolver NPN). The sensor has a connector compatible with the Grove standard. Seeed studio 101020049

The STEVAL-MKI063V1 board enables evaluation of the LSM303DLH sensor, which integrates a 3D accelerometer and magnetometer in a single device. With its USB interface and dedicated software, it serves as a practical tool for spatial orientation analysis and the implementation of electronic compass functions in embedded systems.

The STM32F7 discovery kit allows users to develop and share applications with the STM32F7 Series microcontollers based on ARM® Cortex®-M7 core.

Module with a slide potentiometer. Depending on the position of the slider, the resistance value (maximum resistance 10kΩ) changes, which translates into the voltage value at the analog output of the module. The module has a connector in accordance with the Grove standard. Seeed studio 101020036

A volume sensor designed to detect loud ambient sounds. The module uses a microphone and LM2904 amplifier. The output value (analog signal) depends on the volume of the detected sound. In order to eliminate interference, the microphone signal is subjected to double filtering. Seeed studio 101020063

Mini module with ToF VL53L5CX sensor with a matrix of 64 pixels and a range of up to 4 m. It is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun SEN-19013

LoRaWan and LongFi network monitor. It allows you to specify the number of hotspots to extend the actual network coverage. Seeed Studio 114992777

Module with digital barometer BMP581. It enables pressure measurement in the range from 300 to 1250 hPa with an accuracy of ± 5 Pa and communicates via I2C or SPI. SparkFun SEN-20170

Air quality sensor module based on the ENS160 system. It communicates via the I2C interface (Gravity connector). DFRobot SEN0514

At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much). Adafruit 2796

Expander (shield) compatible with Arduino and NUCLEO (STM32) systems, equipped with a Bluetooth 4.1 (BLE) radio module from the SPBTLE-RF family