Category: STARTER KITS, PROGRAMMERS, MODULES

JTAG / SWD programmer-debugger with USB and WiFi interface. It supports microcontrollers and microprocessors with Cortex-M, Cortex-A, Cortex-R and ARM7, ARM9 and ARM11 cores of most manufacturers as well as 8051, RISC-V, PIC32, RX. Segger J-Link WiFi (8.14.28)

The SparkFun micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I²C and SPI buses. This breakout board for the micro:bit’s edge connector allows to connect the micro:bit to breadboards and other sensors, motors, LEDs and more! BOB-13988

Vibrating sensor module, Plug & Play, omni-directional, designed for switching over low-current circuits. DFRobot DFR0027

Development board based on the MediaTek MT7681 chip. Provides easy access to five GPIO pins and one UART port. The MT7681 module is a compact SoC Wi-Fi system with a built-in TCP / IP stack. Seeed Studio 113990100

Module of the 3-axis LIS2DH, I2C accelerometer. DFRobot SEN0224

Gravity: Formaldehyde (HCHO) Sensor is a module for measuring the concentration of formaldehyde (methane) in the air. It can be supplied with voltage in the range of 3.3 ... 6V. DFRobot SEN0231

Plate from the Adafruit Feather series equipped with an ATmega32u4 microcontroller and a small prototype surface (5x7). The chip contains 32KB flash memory, 2KB RAM memory and built-in USB support. The plate is compatible with Arduino. Adafruit 2771

Adapter enabling easy and quick connection of Modulowo DuoNect expansion modules to selected Atmel Xplained platforms. MOD-82

STM32 Nucleo-144 development board with STM32F722ZE MCU, supports Arduino, ST Zio and morpho connectivity

STM32 Nucleo-64 development board with STM32L073RZT6 MCU, supports Arduino and ST morpho connectivity

Evaluation board with STM32F407 microcontrollerStarter kit equipped with a microcontroller STM32F407IGH6 (1 MB Flash, Cortex-M4), with a built-in programmer-debugger ST-Link/V2, equipped with a 3.2" TFT LCD display and a full set of connectors.

Module with OLED 0.96" display with a resolution of 128x64 px. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 104030008

Micro: Circular RGB LED is an expansion board designed for use with the micro: bit module. It has been equipped with 24 RGB LEDs, a buzzer and a microphone. The board is supplied with voltage in the range of 3.5 ... 5 V. DFRobot ROB0150

Module with blue LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0021-B

Module with rotary potentiometer. The connector in this module has been moved to the other side of the PCB, which makes it easier to assemble and use this module. The module has a connector in accordance with the Grove standard. Seeed studio 101020048

Module allowing collision / vibration detection (based on the MVS0608.02 system). Permitted to detect collisions irrespective of direction, provides high stability and is highly sensitive. The module has a connector in accordance with the Grove standard. Seeed studio 101020005

Module with a humidity sensor. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020018

Module with 9DoF LSM9DS1 sensor (3-axis accelerometer, 3-axis magnetometer, 3-axis gyroscope). It has a derived I2C interface and is supplied with the voltage of 3.3 V. SparkFun DEV-13629

The sensor is designed for indoor air quality testing. The main gas detected is carbon monoxide, alcohol, acetone, thinner, formaldehyde and other slightly toxic gases. It is compatible with 5V and 3.3V power supply. Seeed Studio 101020078