Category: STARTER KITS, PROGRAMMERS, MODULES

Arduino Breakout for LinkIt Smart 7688 Duo is the base board for Seeed Studio IoT modules. The board allows you to easily use the interfaces of the LinkIt Smart 7688 Duo module, is equipped with Ethernet socket, USB socket and Grove standard connectors. Seeed Studio 103030033

At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip. Adafruit 3179

ESP8266-DevKitS – a board for quick programming and launching of ESP8266 modules without soldering. Ideal for IoT prototyping. Espressif ESP8266-DevKitS

Pin expander designed for Feather plates. It is equipped with three sets of female strips and holes for prototyping. Adafruit 3417

The sensor is designed for indoor air quality testing. The main gas detected is carbon monoxide, alcohol, acetone, thinner, formaldehyde and other slightly toxic gases. It is compatible with 5V and 3.3V power supply. Seeed Studio 101020078

STM32 Nucleo-144 development board with STM32H7A3ZI MCU, supports Arduino, ST Zio and morpho connectivity. STMicroelectronics NUCLEO-H7A3ZI-Q

A small module with a temperature sensor (thermistor). As the temperature changes, the resistance of the thermistor changes, which allows the temperature to be measured in the range from -40 to 125 ° C with an accuracy of 1.5 ° C. The module has a connector in accordance with the Grove standard. Seeed studio 101020015

A device with modifiable functionality that works under the control of the NodeMCU ESP32 system. It combines two wireless technologies: Bluetooth 4.1 and WiFi. iNode MCU USB

Ethernet MQTT communication module designed for M5Stack sets. It communicates via the UART interface using AT commands. M5Stack U129

Sound module supported by I2C interface, which allows to generate sound signals in simple projects thanks to Qwiic system and ATtiny84 microcontroller. With support of Arduino libraries, users can control volume, frequency and duration of sound, which makes it ideal for applications such as alarms or signals in robots. SparkFun BOB-24474

A volume sensor designed to detect loud ambient sounds. The module uses a microphone and LM2904 amplifier. The output value (analog signal) depends on the volume of the detected sound. In order to eliminate interference, the microphone signal is subjected to double filtering. Seeed studio 101020063

Module with tact switch button. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020003

Adapter with micro SD card slot. It is equipped with connectors compatible with Teensy LC, 3.0, 3.1, 3.2, 3.5 and 3.6 boards and WIZ820io or WIZ850io Ethernet modules. WIZ820-SD-ADAPTOR

Module allowing collision / vibration detection (based on the MVS0608.02 system). Permitted to detect collisions irrespective of direction, provides high stability and is highly sensitive. The module has a connector in accordance with the Grove standard. Seeed studio 101020005

Analogue temperature and humidity sensor module based on SHT30 sensor. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers, such as Arduino, micro:bit, ESP32. DFRobot DFR0588

IoT development board equipped with ESP32 chip with WiFi and Bluetooth, has a USB-UART interface allowing programming via the USB port of the computer. DFRobot DFR0625

SparkFun Qwiic kit. Contains 10 wires of different lengths and tips. It allows you to connect Qwiic modules to a programming platform or to a prototype board. SparkFun KIT-15081

An expansion board designed for the STM32 Nucleo based on the Teseo-VIC3DA, a global navigation satellite system (GNSS) chip. STMicroelectronics X-NUCLEO-GNSS2A1

Compact ISP programmer for AVR microcontrollers. Works with Atmel Studio, AVRDUDE and Arduino IDE environments, using the STK500 protocol. Has a USB-TTL adapter function. Pololu 3172

Module with a humidity sensor. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020018