Category: STARTER KITS, PROGRAMMERS, MODULES

Board with digital outputs designed to work with STM32 Nucleo. It is based on the IPS1025HF single high-side switch arrangement. STMicroelectronics X-NUCLEO-OUT15A1

Miniature ToF distance sensor based on VL53L0X with 3-200 cm range, 25° field of view and I2C interface for horizontal measurements. M5Stack U196

Terasic HDMI-FMC is a HDMI transmitter/receiver daughter board with FMC (FPGA Mezzanine card) interface

Maxim Octal Relay Driver - Peripheral Module

Evaluation Board with AD7693, 1xADC, 16-bit, Sampling Rate (Per Second) 500k, Analog Devices, RoHS

Evaluation Board with CN0332, Magnetoresistive (MR) Rotational Speed Sensor, Analog Devices, RoHS

MYD-LPC1850 Development Board

The ESP32 WiFi and Bluetooth module has a dual-core 32-bit MCU that integrates WiFi HT40 and Bluetooth / BLE 4.2 technology. Designed for mobile devices and Internet of Things (IoT) applications. DFRobot TEL0111

Analogue temperature and humidity sensor module based on SHT30 sensor. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers, such as Arduino, micro:bit, ESP32. DFRobot DFR0588

PCIe module that allows the Edge TPU coprocessor to be used in existing systems. It allows you to make modern mobile vision models in a power efficient manner. Coral Mini PCIe Accelerator G650-04528-01

Maxim Dual Non-volatile Digital Pot - Peripheral Module

Nucleo-32 series board equipped with STM8S207K8T6C microcontroller with built-in programmer-debugger ST-Link v.2.1, connectors compatible with Arduino Nano.

The Segger J-Link Supply Adapter (8.06.14) allows you to manually set the debug probe I/O voltage, preventing damage to the target board, adjustable from 1.2V to 5.0V. It can be inserted between J-Link or Flasher and the target device, reducing the number of connections needed, which is especially useful in a production environment.

ToF distance sensor module based on the VL6180X system. It offers a range of up to 10 cm and communicates via the I2C interface. Adafruit 3316

The Fio v3 is a new spin on the Arduino Fio hardware powered by the ATmega32U4. Not only is it small and LiPo-ready, it’s a very capable XBee-ready development board. DEV-11520

Optical Time of Flight sensor with Pmod I2C connector. The built-in ISL29501 digital signal processor calculates the time it takes for the light emitted by ToF to reach the destination and back. The calculated time is proportional to the distance. Pmod ToF has a range of up to 5 m. Digilent 410-392

SparkFun weather: bit module designed for micro: bit, with temperature, humidity and pressure sensor (BME280 system). In combination with the micro: bit module, it is possible to build a fully functional weather station. SparkFun DEV-15837

A module dedicated to power analysis of nRF5 series development boards. It is designed to measure and optimize power consumption in embedded device applications. Nordic Semiconductor nRF6707

Evaluation kit with Sparkfun Artemis Bluetooth 5.0 module designed on the basis of the Feather kit. It has a USB C. The board also has a USB-UART converter, a microphone and a JTAG debugging connector. Artemis has support in the Arduino IDE. SparkFun WRL-15574

Evaluation kit with RISC-V Dual Core 64bit chip and WiFi ESP32 chip. Equipped with a USB-UART converter, MEMS microphone, OV2640 camera and a microSD card slot. The set is compatible with Arduino UNO Rev3. Seeed Studio 102991184