Category: STARTER KITS, PROGRAMMERS, MODULES

LPCXpresso55S28 evaluation kit with LPC55S28 microcontroller with ARM Cortex-M33 core. The board contains a built-in LPC-Link2 programmer, audio subsystem, accelerometer, microSD slot, USB interfaces and expansion connectors. NXP LPC55S28-EVK

Heart rate monitor module based on the popular MAX30101 chip. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-16474

Module with a button and green LED backlight. Controlled by the I2C interface, it has a built-in debouncing mechanism, pull-up resistors as well as interrupts and a FIFO queue. SparkFun BOB-16842

Miniature pressure measurement module equipped with a 25 psi piezoresistive pressure sensor. It allows you to perform calibrated and compensated pressure measurements from 60 mbar to 2.5 bar. SparkFun SEN-16476

Module with MOSFET and a Gravity connector. It allows you to easily connect and control the voltage from 5V to 30V and the current up to 2.5A. DFRobot DFR0643

Starter kit with Qwiic modules designed to work with the Raspberry Pi. The set consists of an overlay for Raspberry Pi with a standard 40-pin connector and four Qwiic connectors, OLED display, VCNL4040 distance sensor and environmental sensors. SparkFun KIT-16841

An expansion board with digital outputs (for industrial applications) designed to work with the STM32 Nucleo kits. The module is based on a single high-side switch IPS160HF. STMicroelectronics X-NUCLEO-OUT08A1

Nucleo-32 series board equipped with STM8S207K8T6C microcontroller with built-in programmer-debugger ST-Link v.2.1, connectors compatible with Arduino Nano.

An expansion board with digital outputs (for industrial applications) designed to work with the STM32 Nucleo kits. The module is based on the IPS161HF double high-side switch. STMicroelectronics X-NUCLEO-OUT10A1

Module with 16x2 characters LCD display and ATMega328p microcontroller. The user can communicate with the module through one of the serial interfaces: UART, I2C or SPI. SparkFun LCD-16396

GPS module with NEO-M9N 92-channel GNSS receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. SparkFun GPS-15712

Module with WiFi and Bluetooth Espressif ESP32 WROOM. It integrates a set of peripheral devices - capacitive touch sensors, Hall sensors, SD card interface, Ethernet, fast SPI, UART, I2S and I2C. SparkFun WRL-15663

Grove module with FSR402 pressure sensor. The board is equipped with a Grove connector with an analog output. Seeed Studio 101020553

Module with an EMG signal detector. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020058

A small module with a PAJ7620U2 gesture detection sensor. Can recognize up to 13 gestures. Communication via the Gravity I2C interface. DFRobot SEN0315

Module with a digital temperature and humidity sensor based on the SHTC3 system. Communication takes place via the I2C interface. SparkFun SEN-16467

Module with the MCP9600 amplifier designed to work with a K-type thermocouple. The module has a PCC connector for connecting this type of thermocouple. I2C communication. SparkFun SEN-16294

Module with digital temperature sensor TMP102. It enables temperature measurement in the range from –40°C to 125°C with an accuracy of 0.5°C. The system communicates via the I2C interface. SparkFun SEN-16304

Module with an ambient light sensor VEML6030 with a measuring range up to 120,000 lx. It enables light measurement with 16-bit resolution. I2C communication. SparkFun SEN-15436

Module with BME280 environmental sensor. It allows you to measure temperature, humidity and pressure. The sensor is equipped with two communication interfaces: SPI and I2C (Qwiic). SparkFun SEN-15440