Category: STARTER KITS, PROGRAMMERS, MODULES

The STEVAL-FKI868V2 evaluation board is based on the S2-LP sub-1GHz ultra-low power low data-rate transceiver suitable for ISM bands and wireless M-Bus. The NUCLEO-L053R8 motherboard is equipped with an STM32L0 low power microcontroller to control the S2-LP

Espruino module with Bluetooth LE based on MDBT42Q system with Nordic Semiconductor nRF52832 microcontroller. The module has a pre-installed JavaScript interpreter. Adafruit 3876

Module with an active buzzer. The board is equipped with a Grove connector and is controlled by a digital signal. Seeed Studio 107020000

The board is equipped with ATSAMD51 microcontroller with ARM Cortex-M4 core and SPI Flash memory, GPIO pins and RGB diode. Adafruit 3857

Gravity: I2C 3.7V Li Battery Fuel Gauge is a module for monitoring the parameters of the Li-ion battery allowing for precise measurement of the flow of charge to / from a 1-source source with an input voltage of 2.5-4.2V. DFRobot DFR0563

An expansion board with several EEPROM memories from the M24xx and M95xx series, designed to work with STM32 Nucleo boards. STMicroelectronics X-NUCLEO-EEPRMA2

STM32 Nucleo-144 development board with STM32H7A3ZI MCU, supports Arduino, ST Zio and morpho connectivity. STMicroelectronics NUCLEO-H7A3ZI-Q

Gravity: Digital IR Receiver Module is a module with an IR receiver operating at 38kHz. The module is supplied with 5V voltage. DFRobot DFR0094

Gravity: Joystick Module V2 is a joystick module with two analog outputs (X and Y axis) and a digital output (Z axis) supplied with 3.3 ... 5V voltage. DFRobot DFR0061

ToF distance sensor module based on the VL6180X system. It offers a range of up to 10 cm and communicates via the I2C interface. Adafruit 3316

Gravity: DS18B20 Temperature Sensor is a module with a temperature sensor compatible with Arduino boards. The module can be supplied with 3.3-5V voltage and measures the temperature in the range -55 ~ 125 ° C. DFRobot DFR0024

A module dedicated to power analysis of nRF5 series development boards. It is designed to measure and optimize power consumption in embedded device applications. Nordic Semiconductor nRF6707

Module with the 3-axis MMA8452Q accelerometer. The system has a user selectable measurement scale of ±2g/±4g/±8g. There are two Qwiic connectors on the board and holes with 2.54 mm raster. SparkFun SEN-14587

The Pmod BLE module is a Bluetooth module with powerful capabilities. Thanks to communication via the UART port, the module can be connected to any platform equipped with this interface. The module is equipped with the Roving Networks RN4870 system, in which a full Bluetooth interface is built-in. Digilent 410-359

Pmod HAT Adapter allows you to attach Pmod extensions to the Raspberry Pi computer. The overlay contains 3 Pmod ports and also allows access to the 40-pin PC expansion connector. Digilent 410-366

IoT development board equipped with ESP32 chip with WiFi and Bluetooth, has a USB-UART interface allowing programming via the USB port of the computer. DFRobot DFR0625

NUCLEO-C092RC is an STM32 Nucleo-64 board with the STM32C092RC microcontroller, designed for projects with a CAN FD interface and low power consumption. ARDUINO and ST morpho connectors facilitate the expansion of embedded systems and prototyping.

The Pmod SF3 provides users with 32 MB of non-volatile memory through the use of Micron\'s NOR Flash memory (N25Q256A). By using the SPI protocol, users can both write to and read from the flash memory. Digilent 410-340

SparkFun weather: bit module designed for micro: bit, with temperature, humidity and pressure sensor (BME280 system). In combination with the micro: bit module, it is possible to build a fully functional weather station. SparkFun DEV-15837