3V/5V voltage level converter module with built-in Step-Up converter. Allows development boards operating at 3V to be connected to a device requiring a higher operating voltage of 5V for I2C communication. Adafruit 5649

OV5640 camera module equipped with a 5 MP sensor and a lens with a wide viewing angle of 72 degrees with autofocus. It is perfect for applications related to security systems and monitoring, but also in robotics. Adafruit 5840

Woven conductive fabric silver-plated nylon with resistance of less than 1 ohm per foot in any direction across the textile. Great for use with FLORA. 20 cm x 20 cm piece. Adafruit 1168

5 mW red diode laser module, displaying intersecting lines (cross). Ideally suited to the construction of a laser level, and thanks to the built-in driver, it is possible to supply voltage from 3 V to 5 V. Adafruit 1058

A 200 mm long FPC extension cable designed to increase the distance between a resistive touchscreen and its controller board. It supports 4-pin FPC cables with a 1 mm pitch, while the cable width is 6 mm. Adafruit 1662

The tag contains a NXP S50 chip and an antenna, and is passively powered by the reader/writer when placed a couple inches away. These can be read by almost any 13.56MHz RFID/NFC reader. Adafruit 360

The OV5640 camera module is equipped with a 5 MP sensor and a lens with a wide viewing angle of 120 degrees and minimal distortion. It is perfect for applications related to security systems, monitoring or recording large areas. Adafruit 5839

Module with a voltage level converter from 5 V to 3.3 V, intended for use in the STEMMA QT/Qwiic system. It has a built-in voltage stabilizer providing 3.3 V power supply with a current of up to 500 mA. Adafruit 5637

Panel Mount USB Cable - B Female to Micro-B Male, length 280mm, RoHS

I2C bus amplifier module based on the LTC4311 system. It enables communication via a popular interface over much longer distances while maintaining high transmission speeds. Adafruit 4756

Capacitive soil humidity sensor with I2C interface powered by 3-5V. Adafruit 4026

Liquid level sensor (maximum measuring depth 124 mm) with analog output. The output voltage varies in proportion to the liquid level. Adafruit 3827

PCB board dedicated to PB86 switches. Allows the installation of 12 switches. They can be used as one panel or separated as single buttons. Adafruit 5631

Module with the OPTIGA TRUST M SLS32AIA cryptographic chip. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4351

A module with a high precision temperature sensor based on the MCP9808 chip. It communicates via the I2C interface. Adafruit 1782

Extension module dedicated to matrix displays with HUB75 interface. Designed for minicomputers Raspberry Pi. Adafruit 3211

A small module with a voltage level converter that allows easy conversion of signals from 3.3V to 5V. It is compatible with a wide range of LED strips, such as NeoPixel. With easy, solderless installation, it supports up to two signal lines, ensuring smooth operation of LEDs at frequencies up to 10 MHz. Adafruit 6066

FRAM chip has 64 Kbits (8 KBytes) of storage, interfaces using SPI, and can run at up to 20MHz SPI clock rates. Each byte can be read and written instantaneously (like SRAM) but will keep the memory for 95 years at room temperature. Adafruit 1897

Real time clock (RTC) module PCF8523. It communicates via the I2C interface. Adafruit 3295

STEMMA QT/Qwiic cable (adapter) for Grove 100 mm long. It enables interoperability between the I2C SparkFun Qwiic and Adafruit STEMMA QT-based system and Seeed Studio\'s Grove boards. Adafruit 4528