Pololu G2 24v19 HP - DC motor controller
ID: 573144
zł2,621.57
Tax included
zł2,131.36 tax excl.
Pololu G2 24v19 High Power is a miniature DC motor controller. Driver's power supply: 6.5 ... 40V. Current efficiency of the module: 19A. The module has protection against back voltage and overvoltage. Pololu 1367
Description
Pololu G2 24v19 High Power is a DC motor controller in the form of a H bridge, built based on N-MOSFET transistors. The module can be supplied with voltage from the range of 6.5 ... 40 V. The maximum continuous current supplying the DC motor is 19 A. The controller does not require additional cooling. The controller module has a current measurement circuit taken by the motor which allows setting the current limit. The motor is controlled by means of RC signal, through the I2C interface, UART interface, USB interface or analog interface. The logic part of the controller works with 3.3 V. The controller software update and configuration is done via the USB interface.
Attention!
The set does not include a USB cable . It should be purchased separately.
properties
- Supply voltage: 6.5 V to 40 V (absolute maximum)
- Continuous output current: 19 A
- Adjustable maximum acceleration and delay
- Adjustable initial and maximum speed
- Possibility of braking or running
- Input calibration for analog and RC signals
- Adjustable threshold and reaction to excessive temperature
- Adjustable PWM frequency from 1.13 kHz to 22.5 kHz
- Error LED connected to the digital ERR output
- Protection against back voltage
- Short-circuit protection
- Current measurement circuit for the motor
- The controller's logic is powered by 3.3V
- Dimensions: 43.2 x 30.5 x 10.7 mm
- Weight: 9.7 g
Included
- The Pololu G2 24v19 driver module
- 2 x 2 pin screw connection
- 2 x male goldpin connector
- jumper
573144
Data sheet
- Output current
- 19 A
- Number of channels
- 1
- Supply voltage min
- 6,5 V
- Supply voltages max
- 40 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3×0.8″ board supports a wide 6.5V to 40V voltage range and is efficient enough to deliver a continuous 13A without a heat sink. Driver includes reverse-voltage protection along with basic current sensing and current limiting functionality. Pololu 2992
zł181.07
Delivery date unknown
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 17 A without a heat sink.
zł184.19
Delivery date unknown
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 25 A without a heat sink.
zł286.68
Delivery date unknown
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 40 V voltage range and is efficient enough to deliver a continuous 21 A without a heat sink.
zł216.36
24h
Available quantity: 1
Available
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1363
zł551.54
24h
Available quantity: 1
Available
Pololu G2 24v12 High Power is a miniature DC motor controller. Driver\'s power supply: 6.5 ... 30V. Current capacity of the module: 12A. The module has protection against back voltage and overvoltage. Pololu 1365
zł559.49
Delivery date unknown
No product available!
Pololu G2 18v25 High Power is a miniature DC motor controller. Driver\'s power supply: 6.5 ... 30V. Current capacity of the module: 25A. The module has protection against back voltage and overvoltage. Pololu 1366
zł677.82
24h
Available quantity: 1
Available
Other products in the same category (16)
DC motor driver with voltage 6.5 ... 40V and maximum continuous current 13A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3147
zł460.81
24h
Available quantity: 1
Available
TB9051FTG Single Brushed The DC Motor Driver Carrier is a single DC motor driver that allows the motor to be supplied with voltage in the 4.5 ... 28V range and power consumption at a continuous 2.6 A (5A peak) operation. Pololu 2997
zł47.04
24h
Available quantity: 1
Available
Two-channel driver for DC motors with an operating voltage from 7 to 45 V and a continuous current of up to 60 A. It can be controlled by an analog signal, PWM, UART, RC or by means of built-in buttons. Cytron MDDS60
zł747.84
4 weeks
No product available!
The ESC RC controller module is designed for brush motors with a supply voltage from 3.5 to 6 V and a capacity of 1 A
zł5.90
24h
Available quantity: 6
Available
The controller enables to supply the motors with voltage in the range of 10-47V and power consumption in continuous operation of 1.7A (4.5A peak) for each channel in dual or 3.4A mode (9A peak) in single channel mode. Pololu 2999
zł56.09
24h
Available quantity: 4
Available
No product available!
KAmod Motor Driver is an advanced DC motor controller powered by 6-30 V, enabling power regulation using the PWM method and control of the direction of rotation, compatible with analog and PWM signals from various sources, equipped with overload and thermal protections and soft start and stop functions
zł61.91
24h
Available quantity: 270
Available
Single-channel DC motor controller enabling motor control with voltage in the range of 7-30V and current up to 10A. The set has a potentiometer and a direction switch. Cytron MD10_POT
zł54.49
24h
Available quantity: 49
Available
A module with a two-channel DC motor driver based on the TB6612FNG system. Designed for Wemos D1 Mini
zł45.61
24h
Available quantity: 3
Available
The RoboClaw motor controller can control a pair of brushed DC motors using USB serial, TTL serial, RC or analog inputs. Integrated dual quadrature decoders make it easy to create a closed-loop speed control system. This version can supply a continuous 7.5 A per channel (15 A peak). Pololu 3284
zł622.84
24h
Available quantity: 1
Available
Pololu Dual G2 High-Power Motor Driver 18v22 is an extension that allows you to control two DC motors designed for Arduino tiles. The motor can be supplied with 6.5 ... 30V voltage and can draw up a maximum current of 22A. Polol 2517
zł598.99
4 weeks
No product available!
No product available!
Tiny breakout board for TI’s DRV8838 motor driver can deliver a continuous 1.7 A (1.8 A peak) to a single brushed DC motor. Operating voltage range from 0 V to 11 V, built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature. Pololu 2990
zł19.56
24h
Available quantity: 1
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for self-assembly. Pololu 5046
zł435.53
4 weeks
No product available!
Dual DC motor controller designed for Arduino, which enables the motor to be supplied with voltage in the 4.5 ... 28V range and power consumption in continuous operation of 2.6 A (5A at the top) of two DC motors. Polol 2520
zł122.25
24h
Available quantity: 1
Available
Dual MAX14870 Motor Driver is a dual DC motor controller compatible with the Arduino standard that allows you to control two DC motors with 4.5 ... 36V continuous current of 1.7A. Polol 2519
zł134.43
24h
Available quantity: 2
Available
Pololu G2 24v19 High Power is a miniature DC motor controller. Driver's power supply: 6.5 ... 40V. Current efficiency of the module: 19A. The module has protection against back voltage and overvoltage. Pololu 1367