Humidity and Temperature Sensor Breakout - Si7021
ID: 561860
zł68.97
Tax included
zł56.07 tax excl.
Ideal for environmental sensing and data logging and perfect for build a weather stations or humidor control system; built-in 4.7KΩ pullup resistors for I2C communications. SEN-13763
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 12:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
The Si7021 is a low-cost, easy-to-use, highly accurate, digital humidity and temperature sensor. This sensor is ideal for environmental sensing and data logging and perfect for build a weather stations or humidor control system. All you need are two lines for I2C communication, and you’ll have relative humidity readings and very accurate temperature readings as a bonus!
There are only four pins that need to be hooked up in order to start using this sensor in a project. One for VCC, one for GND, and two data lines for I2C communication. This breakout board has built-in 4.7KΩ pull up resistors for I2C communications. If you’re hooking up multiple I2C devices on the same bus, you may want to disable/enable the pull-up resistors for one or more boards. On the Si7021, the pull-ups are enabled by default. To disable them, simply use some solder wick to remove the solder on the jumper labeled PU. This will disconnect the resistors from VCC and from the I2C bus.
The Si7021 also comes equipped with a hydrophobic PTFE filter covering the inlet on the sensor. This filter blocks contaminants but allows water vapor to pass through, keeping your sensor safe from water damage while still proving accurate sensor readings.
The tiny white cover on the IC is known as a Polytetrafluorethylene (PTFE) Membrane Filter. It keeps moisture out but allows humidity in. This filter is very low-profile, hydrophobic and oleophobic, and excludes particulates down to 0.35 microns in size.
Attention! Do not remove this white filter, mistaking it for some IC tape that was left on by mistake. Removing the filter may result in a shortened life span of the device or failure in highly humid areas.
Features
- Uses the I2C interface
- Typical humidity accuracy of ±2%
- Typical temperature accuracy of ±0.3C
- Operates from 0 to 100% humidity but this sensor isn’t recommended for harsh environments where it could come in contact with water (such as rain)
- 3.3V sensor - use inline logic level converters or 10kΩ resistors to limit 5V signals
- Only one Si7021 sensor can reside on the I2C bus at a time
- Dimensions: 0.6" x 0.6"
kk-sen-13763
You might also like
Pin header goldpin black 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
zł0.49
24h
Available quantity: 17120
Available
Pin header goldpin black 1x40 pins. Angled connector for through-hole assembly. 2.54mm pitch.
zł0.70
24h
Available quantity: 4401
Available
Available
Wireless temperature sensor with high accuracy with built-in event memory (recorder) with MCP9844 transducer
zł115.31
24h
Available quantity: 2
Available
Other products in the same category (16)
Module with humidity and air temperature sensor based on the AM2302 system. It allows temperature measurement in the range from -40 to 80 ° C and the humidity measurement takes place in the range of 5 to 99% RH. The module has a connector in accordance with the Grove standard. Seeed Studio 101020019
zł70.60
24h
Available quantity: 7
Available
Module with temperature and humidity sensor TH02. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020074
zł70.16
24h
Available quantity: 3
Available
KAmodHTS221 is a module that allows the measurement of humidity and temperature, and thanks to the built-in stabilizer and translator levels, it can be successfully used in systems supplied with a voltage of 2.5 - 5.5 V
zł34.90
24h
Available quantity: 234
Available
Temperature and humidity sensor SHT20 closed in a waterproof housing. Communication via the I2C interface. DFRobot SEN0227
zł144.24
24h
Available quantity: 1
Available
Module with temperature, humidity and pressure sensor BME680 from Bosch. The module communicates via I2C or SPI interfaces.
zł151.45
24h
Available quantity: 4
Available
Analogue temperature and humidity sensor module based on SHT30 sensor. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers, such as Arduino, micro:bit, ESP32. DFRobot DFR0588
zł37.20
24h
Available quantity: 1
Available
Digital temperature and humidity sensor with calibrated digital output signal. Equipped with a 2.5 mm 4-pin male stereo audio connector that works perfectly with the Sonoff TH10/TH16 socket. Sonoff Si7021
zł43.33
24h
Available quantity: 11
Available
Wireless sensor with LoRaWAN network communication. Dedicated to industrial long-distance data acquisition with a wide measurement range of temperature from -40°C to 85°C and humidity from 0 to 100% RH. Seeed Studio 114992867
zł399.00
24h
Available quantity: 2
Available
Module with CO2, temperature and humidity sensor SCD-41. Equipped with a Qwiic/STEMMA QT connector, it communicates via the I2C interface. Pimoroni PIM587
zł339.64
24h
Available quantity: 2
Available
Module with BME680 sensor for measuring the concentration of volatile organic compounds (VOC), pressure, temperature and humidity. I2C or SPI communication. DFRobot SEN0375
zł97.51
24h
Available quantity: 4
Available
Module with a BME680 sensor that allows you to measure temperature, humidity, pressure and gas detection. The board is equipped with a Grove connector and communicates via I2C and SPI. Seeed Studio 101020513
zł136.80
24h
Available quantity: 2
Available
Module with DHT20 temperature and humidity sensor. It allows you to measure humidity in the range from 0 to 100% and temperature from -40 to 80℃. DFRobot SEN0497
zł42.45
24h
Available quantity: 3
Available
SHT35 Digital Temperature & Humidity Sensor Breakout - module with SHT35 temperature and humidity...
Module with a digital temperature and humidity sensor based on the SHT35. Communication via the I2C interface. DFRobot SEN0333
zł97.24
24h
Available quantity: 2
Available
Module with BME280 environmental sensor. It allows you to measure temperature, humidity and pressure. The sensor is equipped with two communication interfaces: SPI and I2C. SparkFun SEN-13905
zł130.80
24h
Available quantity: 2
Available
Module with a digital temperature and humidity sensor based on the SHTC3 system. Communication takes place via the I2C interface. DFRobot SEN0414
zł30.43
24h
Available quantity: 5
Available
Temperature and humidity sensor adapted to work with Sonoff TH10 / TH16
zł52.20
24h
Available quantity: 6
Available
Ideal for environmental sensing and data logging and perfect for build a weather stations or humidor control system; built-in 4.7KΩ pullup resistors for I2C communications. SEN-13763