![SHT20 I2C Temperature & Humidity Sensor - waterproof SHT20 temperature and humidity sensor SHT20 I2C Temperature & Humidity Sensor - waterproof SHT20 temperature and humidity sensor](https://kamami.pl/30302-large_default/sht20-i2c-temperature-humidity-sensor-waterproof-sht20-temperature-and-humidity-sensor-sen0227.jpg)
![SHT20 I2C Temperature & Humidity Sensor - waterproof SHT20 temperature and humidity sensor SHT20 I2C Temperature & Humidity Sensor - waterproof SHT20 temperature and humidity sensor](https://kamami.pl/30302-large_default/sht20-i2c-temperature-humidity-sensor-waterproof-sht20-temperature-and-humidity-sensor-sen0227.jpg)
zł93.29 tax excl.
Temperature and humidity sensor SHT20 closed in a waterproof housing. Communication via the I2C interface. DFRobot SEN0227
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
Temperature and humidity sensor equipped with a waterproof probe. It uses the CMOSens® SHT20 chip and has a built-in amplifier, A / D converter, OTP memory and a digital processor. It is characterized by high reliability and long-term stability. It is equipped with a 10 k pull-up resistor and a capacitor with a 0.1 uF filter, which allows the sensor to be used directly with a microcontroller. It is supplied with the voltage of 3.3 V or 5 V and communicates via the I2C interface. Full documentation with examples of use is available on the product wiki page.
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Module 4-pin sensor adapter. DFRobot FIT0511
Temperature and humidity sensor module based on the HTS221 chip. Equipped with a STEMMA QT connector, it communicates via an I2C or SPI interface. Adafruit 4535
relative humidity sensor with integrated temperature sensor for highly accurate measurements at low power. With the TI HDC1080, you can determine the relative humidity of the environment with up to 14 bits of resolution. Digilent 410-347
No product available!
Precision sensor from Bosch for measuring humidity with ±3% accuracy, barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy Adafruit 2652
Module with temperature, humidity and pressure sensor BME680 from Bosch. The module communicates via I2C or SPI interfaces.
Module with a temperature and humidity sensor based on the HTU31 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4832
Module with a digital temperature and humidity sensor based on the SHT31-F system. Communication via the I2C interface. DFRobot SEN0332
No product available!
Module with BME680 for measuring the concentration of VOC, pressure, temperature and humidity. Equipped with a STEMMA QT connector, it communicates via I2C or SPI. Adafruit 3660
Module with temperature and humidity sensor TH02. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020074
Module with pressure, temperature and humidity sensor BME280. It allows to read the atmospheric pressure in the range from 300 to 1100 hPa and communicates via the I2C or SPI interface. Waveshare BME280 Environmental Sensor
Module with a digital temperature and humidity sensor based on the SHT35. Communication via the I2C interface. DFRobot SEN0333
Module with a temperature and humidity sensor based on the SHT40 system. It communicates via the I2C interface. SEN0428
Module with temperature and humidity sensor DHT11. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020011
Integrated BME688 gas, pressure, temperature and humidity sensor in one MEMS housing. The system can be supplied with the voltage of 3.3 V and is equipped with an I2C communication interface. BME688 Breakout Board
Module with a digital temperature and humidity sensor based on the SHT31-F system. Communication via the I2C interface. Equipped with a Gravity DFRobot SEN0334 connector
Module with a BME680 sensor that allows you to measure temperature, humidity, pressure and gas detection. The board is equipped with a Grove connector and communicates via I2C and SPI. Seeed Studio 101020513
Temperature and humidity sensor SHT20 closed in a waterproof housing. Communication via the I2C interface. DFRobot SEN0227