zł103.33 tax excl.
MQ138 sensor breakout for monitoring air quality and detecting volatile organic compounds, including benzene, toluene, acetone and formaldehyde. Equipped with an ATtiny404 microcontroller and two Qwiic connectors, it communicates over I2C and operates from a 3.3V supply. Provides approximate gas level readings for monitoring changes in air pollution. Soldered 333128
The device MQ138 from Soldered is an air quality sensor breakout for detecting volatile organic compounds such as benzene, toluene, acetone and formaldehyde. Its semiconductor sensing element changes resistance when exposed to gases in the surrounding air. These readings can be used to monitor changes in air pollution levels and develop systems that respond to increasing concentrations.
The onboard ATtiny404 microcontroller reads the sensor signal and provides data over I2C. Two Qwiic connectors, compatible with easyC and STEMMA QT, allow the module to connect to a compatible controller board and additional devices on the same bus without soldering. The default I2C address is 0x30, and onboard switches allow it to be changed within the 0x30–0x37 range.

The manufacturer provides an Arduino library with reading and calibration examples. Gas concentration is estimated in software using the response characteristics of the selected gas. Since the sensor responds to multiple substances, readings are approximate and cannot independently determine the concentration of individual components in a mixture. According to the setup instructions, the sensor should be preheated for approximately 48 hours and then calibrated in clean air.
Data sheet
Total suspended particulate (TSP) sensor that allows you to measure the particle concentration from 1 to 100 μm. SDS198
Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. SparkFun SEN-16531
Module with sensors of environmental parameters. It allows you to measure temperature, humidity and pressure as well as CO2 and VOC concentration. DFRobot SEN0335
Sharp GP2Y1010AU0F dust and particle concentration sensors. It is supplied with the voltage from 5 to 7V. Has an analog output. DFRobot SEN0144
Module with PM2.5 HM3301 dust sensor. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020613
Module with air quality sensor SGP30. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020512
No product available!
Air quality sensor module based on the SGP40 system. It communicates via the I2C interface. DFRobot SEN0392
Module with air quality sensor SGP30. It allows you to read the concentration of VOC (TVOC) and eCO2 and communicates via the I2C interface. Pimoroni PIM480
Air quality sensor module PMSA003I. It allows for a precise analysis of the amount of pollutants in the environment based on the concentration of PM1.0, PM2.5 and PM10 particles. Adafruit 4632
Air quality sensor module based on the SGP40 system. It uses CMOSens technology by Sensirion and provides information on the concentration of volatile organic compounds (VOC). Adafruit 4829
Module with PM2.5 dust sensor. The board is equipped with a Gravity connector and communicates via the I2C interface. DFRobot SEN0460
Module with environmental sensors for Raspberry Pi Pico. It allows you to measure temperature, humidity, air quality pressure and color detection. SB Components 22366
Air quality sensor module PMSA003. It allows you to analyze the amount of pollutants based on the concentration of PM1.0, PM2.5 and PM10 particles. SB Components 21208
Air quality sensor module based on the ENS160 system. It communicates via the I2C or SPI interface. DFRobot SEN0515
Air quality sensor module based on the ENS160 system. It communicates via the I2C interface (Gravity connector). DFRobot SEN0514
No product available!
Module with a Geiger counter that allows the detection of ionizing radiation. Equipped with a Gravity connector. DFRobot SEN0463
MQ138 sensor breakout for monitoring air quality and detecting volatile organic compounds, including benzene, toluene, acetone and formaldehyde. Equipped with an ATtiny404 microcontroller and two Qwiic connectors, it communicates over I2C and operates from a 3.3V supply. Provides approximate gas level readings for monitoring changes in air pollution. Soldered 333128