

zł19.47 tax excl.
Module with a formaldehyde sensor made in MEMS technology. It allows gas detection in the range of 0 to 3 ppm and has an analog output. DFRobot SEN0563
Module with a formaldehyde sensor that uses electromechanical microsystem (MEMS) technology, thanks to which the sensor has a compact size, low power consumption, short acquisition time and fast response. It can measure concentrations from 0 to 3 ppm and is suitable for leak alarms, e.g. in portable gas detectors. The sensor has an analog output and is supplied with a voltage of 3.3 V to 5 V. Full documentation and sample programs are available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553
Module with a knock-on sensor for measurement of methane, propane and carbon monoxide (MQ-9) concentrations. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
Module with ozone detection sensor. It performs measurements up to 10 ppm with a resolution of 0.01 ppm. It has a UART output and an analog output. ZE25-O3
MH-Z16 carbon dioxide sensor with Grove connector. It communicates via the UART interface. Seeed Studio 101020067
Module with an analog MQ4 methane sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0129
Integrated BME688 gas, pressure, temperature and humidity sensor in one MEMS housing. The system can be supplied with the voltage of 3.3 V and is equipped with an I2C communication interface. BME688 Breakout Board
Pololu MQ Gas Sensor Carrier
Module with an ozone detection sensor that performs measurements in the range of up to 10 ppm with a resolution of 0.01 ppm. The module is equipped with an I2C interface. DFRobot SEN0321
No product available!
Module with BME680 sensor to measure the concentration of volatile organic compounds, pressure, temperature and humidity. It communicates via the I2C interface. Pimoroni PIM357
A sensor that detects the concentration of carbon monoxide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0466
No product available!
Sensor that detects the concentration of chlorine. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0468
No product available!
Module with CO2, temperature and humidity sensor SCD-41. Equipped with a Qwiic/STEMMA QT connector, it communicates via the I2C interface. Pimoroni PIM587
Module with four gas sensors that allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020820
Module with a smoke concentration sensor made in MEMS technology. It allows gas detection in the range of 10 to 1000 ppm and has an analog output. DFRobot SEN0570
No product available!
Module with a BME688 sensor for measuring gas concentration, pressure, temperature and humidity. I2C or SPI communication. SparkFun SEN-19096
ENS160 gas sensor module to measure the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via an I2C or SPI interface. SparkFun SEN-20844
Module with an ambient oxygen concentration sensor. The system allows you to measure the oxygen volume in the range up to 25% with a resolution of 0.15%. The module communicates via the I2C interface. DFRobot SEN0322
Module with a formaldehyde sensor made in MEMS technology. It allows gas detection in the range of 0 to 3 ppm and has an analog output. DFRobot SEN0563