New products

Roof-mount LTE MIMO antenna designed for use with compatible Teltonika Networks routers and devices. It supports frequency ranges of 698-960 MHz and 1710-2690 MHz, while two 3 m RG174 cables are terminated with SMA Male connectors. The housing has an IP65 ingress protection rating, excluding the cable outlet, and is UV resistant. Teltonika PR1KCL25

Cable designed for powering and using input/output lines in compatible Teltonika Networks devices. One end features a 4-pin connector with 3 mm pitch, while the other is equipped with a 4-way screw terminal for solderless connections. The cable length is 2 m. Teltonika PR2FK20M

Metal mounting kit designed for installing compatible Teltonika Networks devices on a standard 35 mm DIN rail. The holder is made of low-carbon steel, while its dimensions of 65.2 x 44.2 x 1.5 mm allow routers, modems, gateways and switches to be installed in control cabinets, distribution boards and industrial installations. Teltonika PR5MEC00

Compact mounting kit designed for installing compatible Teltonika Networks devices on a standard 35 mm DIN rail. The holder is made of PP FH44 material, while its compact dimensions of 70 x 25 x 14.5 mm facilitate installation of routers, modems, gateways and switches in control cabinets and industrial systems. Teltonika PR5MEC11

Jetson SUB Mini PC V2 uses the NVIDIA® Jetson Xavier™ NX 8GB module, delivering up to 21 TOPS of AI performance, together with the reComputer J202 carrier board and its extensive set of interfaces. The computer features a 128GB NVMe SSD, WiFi, Gigabit Ethernet, four USB 3.1 ports, HDMI, DisplayPort, M.2 slots and a 40-pin GPIO header. The aluminum enclosure with a heatsink and fan provides active cooling during AI workloads. Seeed Studio 110061461

The Seeed Studio reComputer Rugged J4012 industrial Edge AI computer features NVIDIA® Jetson Orin™ NX 16GB with AI performance of up to 100 TOPS. The IP66-rated design, M12 connectors and protected USB ports support operation in demanding environments, while available interfaces include 5 x Gigabit Ethernet, CAN, RS-232 / RS-422 / RS-485 and digital inputs and outputs. The computer comes with a 128GB NVMe SSD and WiFi 6 module, while the M.2 Key B slot allows expansion with a 5G module.

Compact Edge AI computer - Seeed Studio reComputer Mini J5012 with GMSL equipped with NVIDIA® Jetson AGX Orin™ 64GB delivering up to 275 TOPS of AI performance. The 119 x 119 x 100 mm design provides interfaces for robotics and autonomous systems, including 1GbE, 10GbE, CAN, RS-485, USB, I2S and support for up to 8 GMSL2 cameras. The computer features 64GB eMMC storage, a 128GB NVMe SSD and NVIDIA JetPack 6.2, with support for upgrading to JetPack 7.2. Seeed Studio 100085113

The compact Seeed Studio reComputer Mini J5011 with GMSL Edge AI computer features NVIDIA® Jetson AGX Orin™ 32GB with AI performance of up to 200 TOPS. The 119 x 119 x 100 mm design provides interfaces for robotics and autonomous systems, including 1GbE, 10GbE, CAN, RS-485, USB, I2S and support for up to 8 GMSL2 cameras. The computer features 64GB eMMC storage, a 128GB NVMe SSD and NVIDIA JetPack 6.2, with support for upgrading to JetPack 7.2. Seeed Studio 100020407

BMP180 sensor module for measuring atmospheric pressure from 300 to 1100hPa and temperature from -40 to 85°C. Communication is handled via I2C at a fixed 0x77 address, while two Qwiic connectors provide solderless connection to compatible boards. Altitude can also be calculated from measured atmospheric pressure. Soldered 333060

INA219-based measurement module for monitoring voltage, current, and power in DC circuits. It measures voltages up to 26V and bidirectional current up to ±3.2A using an onboard 0.1Ω shunt resistor. Communication is handled via I2C, while two Qwiic connectors simplify connection to compatible boards. Soldered 333066

RS-232 transceiver module based on the MAX232E, designed for bidirectional conversion between TTL/CMOS logic levels and RS-232 signals. It provides two transmit and two receive channels, allowing simultaneous data transmission and reception. The supply voltage range specified in the documentation is 4.5–5.5V. Soldered 333067

RS-485 transceiver module based on the SN65176BDR, designed for bidirectional data transmission between a microcontroller and an RS-485 bus. It supports data rates up to 20Mbps and communication distances up to 1200m, while the onboard 120Ω termination resistor can be enabled using the JP2 jumper. Supply voltage is 5V. Soldered 333068

5-inch FPV drone designed for freestyle flying, equipped with a SEQURE H743 V2 flight controller based on the STM32H743 microcontroller, a 32-bit 70 A 4-in-1 ESC, an ELRS 2.4G receiver, and the DJI O4 Air Unit Pro digital video transmission system. The 6S version uses S2207 1850KV motors and Gemfan 51466 V2 propellers, while the Heison 5X V2 frame has a 220 mm wheelbase and 8 mm thick arms. The DJI O4 Pro system supports video recording up to 4K at 120 fps, while the ESC runs AM32 firmware. SEQURE SQFPV Heison 5X V2 6S DJI O4 PRO | ELRS 2.4G | AM32

Development board based on the Microchip ATSAMD21G18A microcontroller with a 32-bit ARM Cortex-M0+ core running at up to 48 MHz, 32 KB of SRAM and 256 KB of Flash memory. The Plus version expands the XIAO SAMD21 design with 16 additional GPIOs, providing a total of 30 GPIOs, as well as integrated Li-Ion battery management, dedicated Reset and Boot buttons and a programmable WS2812 RGB LED. It supports Arduino, PlatformIO, MicroPython, CircuitPython and Zephyr while retaining compact dimensions of 21 x 17.8 mm. Seeed Studio 100031394

Development board based on the Raspberry Pi RP2040 microcontroller with a dual-core ARM Cortex-M0+ processor running at up to 133 MHz, 264 KB of SRAM and 2 MB of Flash memory. The Plus version expands the XIAO RP2040 design with 15 additional GPIOs, providing a total of 29 GPIOs, as well as integrated Li-Ion battery management and software-controlled battery voltage monitoring. It supports Arduino, MicroPython, CircuitPython and other development environments while retaining compact dimensions of 21 x 17.8 mm. Seeed Studio 100059977

Compact ultra-low-power development board with Nordic nRF54LM20A, 128MHz Arm Cortex-M33, 512KB RAM, 2MB NVM and 8MB external Flash. Supports Bluetooth LE 6.0, Matter, Thread, Zigbee and NFC, while the Sense version integrates a 6-axis IMU and PDM microphone. Seeed Studio 100018440

Compact low-power wireless module based on the Semtech LR1110 and Nordic nRF52840, designed for long-range IoT applications and location tracking. Supports LoRaWAN, GNSS GPS/BeiDou, passive WiFi scanning and Bluetooth 5.3, enabling both indoor and outdoor positioning. Seeed Studio 114992865

Ring with 12 individually addressable WS2812B RGB LEDs, allowing independent control of the color and brightness of each light point. The module operates at 5V and uses a single-wire data interface, while DIN and DOUT allow additional modules to be daisy-chained. The outer diameter of the ring is 44mm. Soldered 333070

PIR motion sensor module with a detection range of 3–5m and a viewing angle of up to 100°. SOUT and DOUT provide direct and delayed motion detection signals, while an onboard potentiometer allows delay adjustment. Designed for alarm systems, automatic lighting, and circuits responding to presence or movement. Soldered 333083

MCP4018 digital potentiometer module with 5kΩ nominal resistance and 128 adjustment steps. I2C control enables software-based resistance adjustment, while two Qwiic connectors simplify integration with compatible boards. Designed for adjusting signal levels and analog circuit parameters from a microcontroller. Soldered 333090