Category: STARTER KITS, PROGRAMMERS, MODULES

Function module designed for MicroMod boards. It allows you to add WiFi wireless communication based on the ESP32 chip to the project. SparkFun WRL-18430

An expansion board designed for MicroMod main modules. It is equipped with a Qwiic connector and one place for attaching functional modules. SparkFun DEV-18575

Module with PM2.5 dust sensor. The board is equipped with a Gravity connector and communicates via the I2C interface. DFRobot SEN0460

A set with a radio transmitter and receiver operating at 433 MHz. The modules are equipped with Gravity connectors and communicate via a digital interface. DFRobot TEL0140-1

Adafruit Feather M0 WiFi - ATSAMD21 + ATWINC1500 is a development board with a 32-bit ATSAMD21G18 microcontroller based on Cortex-M0 core. The board also has an ATWINC1500 module that provides WiFi connectivity. Adafruit 3010

An expansion board designed for FireBeetle M0 and ESP32-E kits. The board has 12 GPIO pins, 5 ADC, UART, I2C and SPI interfaces. The pins are color coded according to the Gravity standard. DFRobot DFR0762

UART-RS485 converter module based on the TD (H) 541S485H chip. Equipped with power isolation and TVS. DFRobot DFR0845

Low-power, 2.4GHz spectrum wireless protocol that you can use with iOS without needing special certification. Supported by all modern smart phones - excellent for use in portable projects that will make use of an iOS or Android phone or tablet; it also is supported in Mac OS X and Windows 8+. Adafruit 2995

DC-DC Step-Down Converter ME3116AM6G with an output voltage of 5 V, input voltage from 6 to 24 V and a maximum output current of 1 A. Dedicated to the M5Stack modules. M5Stack U125

The module with SSR BT136S relay with a load of up to 2 A, designed for M5Stack sets. The board is equipped with a Grove connector and is controlled by a digital input. M5Stack U122

The expansion module is designed to work with the micro:bit educational board. It allows you to build an electronic piano

Module with a black and white OLED display 1.3" with a resolution of 128x64 pixels. Designed for M5Stack sets. It communicates via the I2C interface. M5Stack U119

Module with waterproof barometer LPS33HW. It enables pressure measurement in the range from 260 to 1260 hPa and communicates via I2C or SPI. Adafruit 4414

Module with a 6-axis IMU sensor (accelerometer and gyroscope) that allows you to measure acceleration and rotational speed in a wide range of ±30g and ±4000dps. Communicates via I2C. Adafruit 4464

Module with a pressure, temperature and humidity sensor based on the MS8607. Equipped with a STEMMA QT connector, it communicates via the I2C. Adafruit 4716

Module with MLX90614-DCC sensor for non-contact temperature measurement in the range from -70℃ to 380℃. I2C communication. DFRobot SEN0206

Module with ATSAMD21G18 microcontroller and 900 MHz wireless transceiver. The module can be used for transmission in the ISM 868 MHz band after the appropriate software configuration. The ATSAMD21G18 microcontroller (ARM Cortex-M0) is clocked at 48 MHz and operates at 3.3 V. Adafruit 3176

Module with CO2, temperature and humidity sensor SCD-41. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5190

Module with CO2, temperature and humidity sensor SCD-40. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5187

Module with WiFi Espressif ESP32-S2. It integrates two 3.3 V stabilizers, SPI Flash memory, LiPo charging circuit, light sensor and RGB diode. It is equipped with a STEMMA QT connector. Adafruit 4769