Category: STARTER KITS, PROGRAMMERS, MODULES

Module with a GPS receiver based on the MTK3333 system. Dedicated to Feather plates, communicates via the UART interface. Adafruit 3133

M5Stack series kit equipped with ESP32 and camera with OV3660 sensor. It has a built-in W5500 chip and can be powered by the RJ45 (PoE) connector. M5Stack U121-B-V11

Capacitive soil moisture sensor with pump for M5Stack sets, equipped with holes compatible with LEGO. M5Stack U101

7-segment display controller, allowing communication over the I2C bus. Allows you to limit the pins needed to control the display. Adafruit 3088

Development board specially designed to add advanced hardware I/O capabilities to your Android or PC application; PIC microcontroller connects an app on your PC or Android device to low-level peripherals like GPIO, PWM, ADC, I2C, SPI, and UART. DEV-13613

Adafruit Feather 32u4 RFM95 is a development board with built-in ATmega32u4 AVR microcontroller (8MHz, 32kB Flash, 2kB RAM) and RFM95W module enabling wireless communication in the 868 MHz or 915 MHz band. The board is compatible with Arduino IDE. Adafruit 3078

Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 2895

A module that allows you to create your own layout based on the Feather tile. Equipped with prototype holes and a set of screw connectors with pins out. Adafruit 2926

WiFi wireless communication module compatible with the pin spacing of XBEE modules. The module is powered by 3.3 V. The product is compatible with Arduino. DFRobot TEL0092

Module with color sensor TCS3472. The board is equipped with a Grove connector and communicates via the I2C interface. M5Stack U009

Data logger dedicated to Feather plates. Equipped with RTC clock, battery slot and micro SD card slot. Adafruit 2922

This module enables the Feather series range to be expanded with 8 12-bit PWM outputs that can be used, for example, to control servos or LED diodes. Adafruit 2928

This is the FeatherWing OLED: it adds a 128x32 monochrome OLED plus 3 user buttons to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight. Adafruit 2900

ToF distance sensor (Time of flight) with a range of up to 5 m. The module is supplied with the voltage of 3.3 V and communicates via the I2C interface. SparkFun SEN-19218

Ring light with 16 RGB diodes WS2812B type controlled by serial signal. The module can be powered with the voltage from 3.3 V to 5 V, only one signal line is required to control it. DFRobot DFR0888-16

The board features bi-directional motor control using a TB6612 dual H-bridge, so it can control one stepper motor or two brushed DC motors with 4.5-13VDC power and about 1A current draw per motor. Adafruit 2653

Prototype board designed to cooperate with Particle Photon. The board has prototype holes with a 2.54 mm pitch and pins of the I2C interface. SparkFun DEV-13598

Particle’s IoT (Internet of Things) hardware development kit, the Photon, provides everything you need to build a connected project. Particle has combined a powerful 120Mhz ARM Cortex M3 micro-controller with a Broadcom Wi-Fi chip in a tiny thumbnail-sized module called the PØ (P-Zero)

Tiny (18 x 44 mm) breadboard-friendly development board, easy to use, hacker friendly. ATmega328 brains32KB of flash (1/2 K is reserved for the bootloader), 2KB of RAM, clocked at 16MHz. Adafruit 2590

Module with ePaper 2.9" display and RP2040 microcontroller. Equipped with QW/ST connector. Accessories included. Pimoroni PIM610