Category: STARTER KITS, PROGRAMMERS, MODULES

At the Feather 32u4\'s heart is ATmega32u4 clocked at 8 MHz and at 3.3V logic. This chip has 32K of flash and 2K of RAM, with built in USB so not only does it have a USB-to-Serial program & debug capability built in with no need for an FTDI-like chip, it can also act like a mouse, keyboard, USB MIDI device, etc. Adafruit 2795

Gravity: 360 Degree Hall Angle Sensor is a rotation angle sensor measuring a value in the range of 0-360 ° with an analogue output, powered by 5V. DFRobot SEN0221

STM32 Nucleo-144 development board with STM32F412ZG MCU, supports Arduino, ST Zio and morpho connectivity

Linklt Smart 7688 is an IoT module with WiFi interface based on the MediaTek MT7688 system operating under the control of the distribution of the Linux operating system derived from OpenWrt. LinkIt Smart 7688 is a great base for creating complex IoT projects or a smart home. Seeed Studio 102110018

nRF52 DK is a development board based on the nRF52832 system with Bluetooth Low Energy (BLE) and 2.4 GHz connectivity. The module has a connector compatible with Arduino shields, a connector for connecting an external antenna for NFC, buttons and diodes available to the user

A module dedicated to power analysis of nRF5 series development boards. It is designed to measure and optimize power consumption in embedded device applications. Nordic Semiconductor nRF6707

ToF distance sensor module based on the VL6180X system. It offers a range of up to 10 cm and communicates via the I2C interface. Adafruit 3316

The X-NUCLEO-IHM12A1 is a low voltage dual brush DC motor driver expansion board based on the STSPIN240 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys

Gravity: UART Infrared CO2 Sensor is a high precision CO2 sensor. It uses the UART interface for communication. It allows to measure CO2 content in the air in the range of 0 ... 50000ppm. DFRobot SEN0220

Terasic HDMI-FMC is a HDMI transmitter/receiver daughter board with FMC (FPGA Mezzanine card) interface

DFRobot SEN0209

Resistive soil moisture sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020008

A volume sensor designed to detect loud ambient sounds. The module uses a microphone and LM2904 amplifier. The output value (analog signal) depends on the volume of the detected sound. In order to eliminate interference, the microphone signal is subjected to double filtering. Seeed studio 101020063

Qwiic Cable - 500mm

MH-Z16 carbon dioxide sensor with Grove connector. It communicates via the UART interface. Seeed Studio 101020067

Module with an analog current sensor. Enables measurement of alternating and direct current up to 20 A. DFRobot SEN0214

The SparkFun Roshamglo is the new and fun way to play Rock-Paper-Scissors with your friends! The board uses the ATtiny84, and has an IR LED and receiver to communicate between badges. KIT-14130

The Pmod SF3 provides users with 32 MB of non-volatile memory through the use of Micron\'s NOR Flash memory (N25Q256A). By using the SPI protocol, users can both write to and read from the flash memory. Digilent 410-340

Evaluation board with ATSAMD21 microcontroller with ARM Cortex M0 core. Equipped with motion, temperature, light, sound sensors and RGB diodes. Can be programmed in MakeCode, CircuitPython, Arduino IDE or CS Discoveries. Adafruit 3333

Nano I / O Shield for Arduino Nano is an expansion board for Arduino Nano that provides digital, analog pins, power inputs and a connector for the Bluetooth module. DFRobot DFR0012