Category: STARTER KITS, PROGRAMMERS, MODULES

The expansion module is designed for micro:bit sets. Offers a simple, beginner-friendly robotics controller. SparkFun DEV-15713

Prototype kit for use in industry. It includes a prototype board with an M-BUS connector, TTL-RS485 converter, connectors and a DIN rail. M5Stack Base26

Lipo battery with a capacity of 750 mAh for the M5Stack sets. Modules can be connected in parallel and stacked. M5Stack M002

MicroMod main module equipped with Bluetooth 5.0 Sparkfun Artemis. Equipped with an M.2 connector, it can work with MicroMod expansion boards. SprakFun DEV-16401

DM300018 is a versatile development kit designed for testing and prototyping projects using dsPIC30F microcontrollers. It enables the development of applications in the areas of control, data acquisition, and communication within the MPLAB IDE environment.

Module with blue LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0031-B

Set for IR communication. It consists of an IR receiver module and a remote control. DFRobot DFR0107

Marcin. Bonds

Module with yellow LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0031-Y

Extension module for STM32 Nucleo based on a two-channel SIO transceiver and IO-Link PHY L6364Q with built-in voltage stabilizers and a DC-DC converter. STMicroelectronics X-NUCLEO-IOD02A1

Replacement body for the StackChan desktop robot; two feedback servos providing 360° horizontal rotation and 90° vertical tilt; 550 mAh battery; 12 RGB LEDs; infrared transmitter and receiver; three capacitive touch pads; NFC interface; GPIO and UART ports; USB Type-C connector for power and data transmission; dimensions of 48 x 60.1 x 70.4 mm. M5Stack A180

STM3210B-PFSTICK is a compact evaluation platform with the STM32F103R microcontroller, enabling performance analysis and peripheral testing via the DashBoard interface as well as full application debugging in the Hitex environment. The kit is suitable for learning, prototyping, and evaluating STM32 microcontroller features.

Atmel AT91SAM7L-STK Starter Kit

Nordic Semiconductor development kit featuring the nRF7002 WiFi 6 companion IC and a dual-core nRF5340 SoC operating as the host processor. The board supports WiFi, Bluetooth Low Energy, Bluetooth Mesh, NFC, Thread and Zigbee, and includes an onboard SEGGER J-Link programmer/debugger. The Arduino Uno Rev3-compatible form factor facilitates expansion of IoT prototypes. Nordic Semiconductor nRF7002-DK

Module with 4 Qwiic connectors for Teensy boards. Communication via the I2C interface. SparkFun DEV-17119

Module with an analog sensor of carbon monoxide and combustible gases (methane, propane) MQ9. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0134

IO expansion module designed for use with the micro:bit educational development board. The board exposes 20 IO pins along with 3.3 V power and GND lines, enabling direct connection of sensors and electronic modules. The design includes a built-in passive buzzer and a voltage stabilization circuit allowing the module to be powered via a 6–12 V DC connector or a microUSB port

Module with 12-position rotary switch. It is supplied with the voltage ranging from 3.3 V to 12 V and has an analog output (Gravity connector). DFRobot SEN0156

STMicroelectronics STEVAL-FSM01M1 dual-channel digital I/O module designed for the development and testing of industrial digital input and output circuits used in automation and functional safety systems. The board provides two inputs compliant with IEC 61131-2 Type 1 and 3 and two outputs rated at 0.5 A and 2 A. The ST morpho-compatible interface enables operation with STM32 Nucleo boards, while galvanic isolation separates the logic section from the process-side circuitry. STMicroelectronics STEVAL-FSM01M1