Audio amplifier module with three output channels. It can be powered with the voltage from 12 to 18 V and has two outputs with a power of 10 W (left and right) and one with a power of 20 W (bass)

Step-Down converter module converts input voltage (5-23V) to adjustable output voltage (0-16.5V) with maximum current 3A, featuring high precision (1%) and efficiency (up to 95%). Compact size and display make it ideal for various applications, e.g. DIY projects

Pmod MicroSD is a module with a microSD memory card reader. With the help of the module it is possible to read and write data on the microSD memory card without limiting the file system or the maximum card size. The SPI interface is used for communication. Digilent 410-380

Compact expansion with advanced data monitoring features, equipped with temperature, humidity, light sensors and RTC clock. With low power consumption, battery monitoring function and I2C protocol support, it is ideal for long-term battery-powered projects, offering precise measurements and efficient power management. Seeed Studio 114993446

DC-DC step-down converter module 12V 12A used to convert energy from 15-24V input voltage to stable 12V, providing up to 12A current. Thanks to high conversion efficiency (over 90%) and low ripple (<50mV), it is ideal for powering sensitive devices in applications such as robotics, drones or LED lighting systems. Additionally, built-in overheating and short-circuit protection mechanisms ensure reliable operation even in difficult conditions. DFRobot DFR1208

Two axis stepper motor driver expansion board based on the L6470 for STM32 Nucleo

A module enabling the conversion of input voltage in the range from 1.8 V to 5.3 V into the appropriate negative output voltage. It offers high efficiency in excess of 80%, making it ideal for applications where a lower power negative supply is required, such as biasing sensors or op-amp circuits. Pololu 2839

Compact ESP32 based board designed for lighting and WLED projects, offering WiFi, Bluetooth and efficient power supply via USB Type-C (up to 4A). It offers two LED outputs with logic level conversion, a built-in I2S microphone, STEMMA QT port, button, NeoPixel and additional GPIO pins. With support for multiple platforms (Arduino, MicroPython, CircuitPython, ESP-IDF), it is ideal for wearable devices and interactive projects. Adafruit 6160

The module is equipped with eight 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. The board recommended for use with Arduino enables the control of eight relays using only two microcontroller lines. ICSTATION ICSE014A

Crowtail-Sound Sensor 2.0 is an analog sound sensor with a built-in amplifier, intended for measuring sound intensity levels. Ideal for interactive projects, sound-responsive systems and acoustic monitoring.

RTC clock module with PCF8563 chip and battery

The Si5351A clock generator is an I2C controller clock generator. It uses the onboard precision clock to drive multiple PLL\'s and clock dividers using I2C instructions. Adafruit 2045

The S7V8F3 step-up/step-down converter regulates the voltage at 3.3 V, supporting an input voltage range of 2.7 V to 11.8 V, making it ideal for battery-powered applications. With an efficiency of over 90% and protection against short circuits and overheating, it provides reliable and energy-efficient operation in a wide range of conditions. Pololu 2122

An efficient step-down converter that steps down the input voltage from as low as 45 V to a regulated output voltage range of 1.4 to 7 V, offering high efficiency and a maximum continuous current of 3.4 A. It has built-in reverse polarity, overload and short circuit protection, and the spread spectrum function reduces EMI interference. Pololu 4873

The TPA3116D2 amplifier module is a digital class D amplifier, offering 2x50W of power for stereo channels and 100W for the subwoofer, powered by 12V-24V. Thanks to the built-in NE5532 low-pass filter, it provides clean bass sound, and three potentiometers allow you to adjust the volume and cutoff frequency.

The EEPROM memory module with the built-in AT24C32D chip allows storing data without loss after switching off the power supply. MOD 50

A compact breadboard power supply module offering stable 3.3V and 5V outputs and real-time voltage, current and power monitoring via the built-in LCD display. Compatible with Seeed Studio XIAO boards and featuring plug-and-play functionality, the device is ideal for efficient prototyping with full control over power parameters. Seeed Studio 114993507

Finger Vein Scanner Module (A) is an advanced biometric module for finger vein identification, offering a high level of security, low power consumption, and resistance to harsh environmental conditions. Its fully integrated design and support for standard communication protocols facilitate its use in smart locks, access control systems, and embedded devices, especially in applications requiring reliable user authentication without contact with the skin surface.

7-inch HMI display module with touch panel dedicated to industrial applications. It offers a resolution of 1024x600 pixels. It is adapted to work in temperatures from -20℃ to 60℃, thanks to its solid housing and fanless design. Edatec ED-HMI3010-070C-0000

DFRobot DFR1193 module with the LTC4316 chip enables the simultaneous use of multiple identical I2C sensors without address conflicts. It supports quick configuration via DIP switches or resistors, offering a flexible and reliable solution for IoT, robotics, and automation projects.