Motoron M2U550 Dual Serial Motor Controller - 2-channel DC motor controller (soldered connectors)
ID: 1185695
zł86.42
Tax included
zł70.26 tax excl.
A two-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors. Pololu 5080
Description
A DC motor controller that allows the movement of two drives to be controlled via a UART TTL interface. It can operate with motors with supply voltages from 1.8 to 22 V and has a capacity of up to 1.6 A per motor (continuous operation). The controller has built-in protection in case of loss of communication with the main controller and a configurable response if an error occurs. The user can set the maximum acceleration and initial speed of the motor Using a single UART bus, it can control several modules. A user manual and a library with example programmes are available on the manufacturer's website.
Features
- Operating voltage range: 1.8 V to 22 V
- Maximum output current per motor: 1.6 A continuous, 5 A instantaneous
- Voltage range of the logic part: 3 V to 5.5 V
- Control interface: UART TTL, up to 250 kbps
- CRC control possible
- Configurable motion parameters:
- Maximum acceleration/deceleration
- Initial speed
- Delay for change of direction
- PWM frequency: eight options from 1 kHz to 80 kHz available
- Protection in case of communication loss
- Configurable automatic error response
- Measurement of motor supply voltage (VIN)
- Two status LEDs
- Motor direction LEDs
- Dimensions: 15.24 x 20.32 mm
1185695
Data sheet
- Output current
- 1,6 A
- Number of channels
- 2
- Supply voltage min
- 1,8 V
- Supply voltages max
- 22 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A two-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors for assembly. Pololu 5081
zł78.95
24h
Available quantity: 2
Available
A two-channel DC motor controller with a I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors for assembly. Pololu 5079
zł78.72
24h
Available quantity: 1
Available
A two-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with soldered connectors. Pololu 5078
zł86.42
24h
Available quantity: 2
Available
Other products in the same category (16)
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5059
zł411.99
4 weeks
No product available!
Pololu Jrk 12v12 USB Motor Controller with Feedback
zł977.65
24h
Available quantity: 2
Available
Raspberry Pi Expansion Board, DC Motor / Stepper Motor Driver
zł115.66
24h
Available quantity: 2
Available
Single-channel DC motor driver with an operating voltage from 10 to 45 V and a continuous current up to 40 A. It can be controlled by an analog signal, PWM, UART, RC or by means of built-in buttons. Cytron MDS40B
zł341.31
24h
Available quantity: 2
Available
DC motor controller powered with a voltage in the range of 1.8 to 10V with a maximum output current of 2.6A. Compatible with STM32 Nucleo. Shield is equipped with a connector compatible with the Arduino UNO R3 standard. STMicroelectronics X-NUCLEO-IHM13A1
zł95.96
24h
Available quantity: 2
Available
3-channel brush motor controller module with PWM signal mixing function. It allows you to control three DC motors with a current consumption of up to 3 A per channel
zł52.31
4 weeks
No product available!
The high power motor driver module works on the basis of Infineon BTS7960B systems. Maximum controller current: 43 A, operating voltage range: 5.5V - 27V. The module has a heat sink and can be controlled from the Arduino, Raspberry Pi, and STM levels. IBT_2
zł39.30
24h
Available quantity: 1
Available
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1362
zł500.01
24h
Available quantity: 1
Available
DC motor driver that allows you to control the movement of three drives using the I2C interface. Board with soldered connectors. Pololu 5030
zł223.10
4 weeks
No product available!
HAT with TB6612FNG engine controller and PCA9685 PWM controller designed for Raspberry Pi minicomputers. The board is equipped with a 40-pin connector characteristic of Raspberry Pi, making it compatible with all minicomputers with this connector. Waveshare Motor Driver HAT
zł67.00
24h
Available quantity: 2
Available
Dual DC motor controller with voltage from 2.5 to 9.5V with 1A continuous current per channel. Has an embedded voltage regulator. Cytron Maker Drive
zł17.84
24h
Available quantity: 11
Available
Module with a 2-channel driver for DC motors L293D designed to work with the Raspberry Pi Pico. It can work with a voltage from 6 to 12 V and a current of up to 600 mA. SB Components 21468
zł85.90
24h
Available quantity: 1
Available
The DC motor driver module enables the motor to be controlled using a PWM signal with several supply voltages (3V, 6V, 12V, 24V and 35V) and a maximum continuous current of 5A.
zł7.81
24h
Available quantity: 20
Available
A single-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with soldered connectors. Pololu 5074
zł68.14
24h
Available quantity: 2
Available
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 40 V voltage range and is efficient enough to deliver a continuous 21 A without a heat sink.
zł216.36
24h
Available quantity: 1
Available
DC motor driver that allows you to control the movement of three drives using the I2C interface. The set includes only the board without connectors. Pololu 5032
zł177.08
4 weeks
No product available!
A two-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors. Pololu 5080