The largest starter set for working with Raspberry Pi computers, rich in modules and assembly lines, compatible with Linux and Windows 10 IoT systems, is CE-certified. Seeedstudio 103010002

The module allows the detection of volatile organic compounds (VOC) in the air, based on Winsen\'s WSP2110 system. Allows for detection in the air; formaldehyde (HCHO), methane, benzene, toluene, alcohol, etc. The sensor output is an analog signal. Seeed studio 101020001

Module with the LIS2DW12 3-axis accelerometer. The system has a user selectable measurement scale of ± 2g/±4g/±8g/±16g. There is a Gravity connector on the board. DFRobot SEN0409

Module with BME680 sensor for measuring environmental conditions such as concentration of volatile organic compounds (VOC), atmospheric pressure, temperature and humidity. I2C or SPI communication. SparkFun SEN-16466

Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. SparkFun SEN-16531

Module with 9-axis IMU ICM-20948 sensor. The chip is an integrated 3-axis accelerometer, gyroscope and magnetometer and a digital motion processor DMP (Digital Motion Processor). Communication via I2C or SPI. SparkFun SEN-15335

A set with a temperature sensor based on the DS18B20 system in the form of a waterproof measuring probe, a sensor adapter and a cable. Communication via the 1-Wire interface. DFRobot KIT0021

Module with BME280 environmental sensor. It allows you to measure temperature, humidity and pressure. The sensor is equipped with two communication interfaces: SPI and I2C (Qwiic). SparkFun SEN-15440

A mini module with a Qwiic connector designed for Raspberry Pi minicomputers. Qwiic SHIM uses a unique connector that snaps into the GPIO connector for a secure, solder-free connection. SparkFun DEV-15794

Pmod MicroSD is a module with a microSD memory card reader. With the help of the module it is possible to read and write data on the microSD memory card without limiting the file system or the maximum card size. The SPI interface is used for communication. Digilent 410-380

Gravity: Analog Sound Sensor is a sound sensor with Gravity analogue output. The module can be supplied with 3.3 ... 5V voltage. DFRobot DFR0034

A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513

Module with temperature and humidity sensor DHT11. It allows you to measure humidity in the range of 20 ... 90% and temperature (0 ... 50 ° C). DFRobot DFR0067

Module with the OPTIGA TRUST M SLS32AIA cryptographic chip. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4351

A module with a temperature and humidity sensor based on the AHT20 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4566

Module with EEPROM memory, capacity 512 kbit (64kB). Communication takes place via the I2C interface. The module has 3 jumpers that enable selection of one of 8 addresses. SparkFun SPX-14764

Gravity: I2C 12-Bit DAC is a module with 12-bit DAC and built-in EEPROM memory. The module is powered by 3.3 ... 5V for communication used by the I2C interface. DFRobot DFR0552

Module with a button, LED diode and a red cap. DFRobot DFR0029-R

Gravity sensor adapter with 3-pin terminal connector. There are two 10 kΩ pull-up and pull down resistors on the board, set with a jumper. DFRobot DFR0055

Gravity: Digital Capacitive Touch Sensor is a capacitive touch sensor powered by 3.3V ... 5V voltage. DFRobot DFR0030