Board with goldpin connectors designed for micro:bit sets. It enables connection of a micro: bit set and attaching a module with connectors, eg to a contact plate. Adafruit 3695

Compact stepper motor controller with the TMC2208 system with an operating voltage from 4.75 to 36 V. It offers smooth, quiet operation, high efficiency, various operating modes and easy configuration. It is controlled via the STEP/DIR interface and is an ideal solution for 3D printers and similar applications. BIGTREETECH TMC2208 V3.0

The adapter allows to extend the CSI / DSI interface using two FFC tapes (by connecting them in one tape). It allows you to connect the camera to a Raspberry Pi computer or a DSI display, for distances using two FFC tapes. Adafruit 3671

The S9V11F3S5CMA switching step-up/step-down regulator efficiently produces a fixed 3.3 V (default) or 5 V (selectable) output whether it is higher or lower than the input voltage, which can range from 2 V to 16 V. (Note: minimum start-up voltage is 3 V, but it operates to 2 V after that.)

Wireless transceiver operating in the 915MHz band based on the RFM69HCW chip with a maximum power of 100mW and a transmission speed of up to 300kbps. The range in open space is up to 500m. The module communicates via the SPI bus. Arduino compatible. modRFM69HCW_915MHz

4-core cable, 20 cm long, terminated on both sides with a Grove plug. Compatible with the interface used in Seeed Studio and M5Stack modules. Seeed Studio 110990027

The camera module is based on a CMOS sensor - AR0134. It has a resolution of 1280 x 960 px (1.2 MPx). The module supports recording of video sequences: 1280 x 960 @ 54fps and 1280 x 720 @ 60Ffps. Intended for use only with the ArduCam USB Shield module. Arducam B0100

The 3.3V 3A Step-Down Converter Module is an efficient and compact solution for 3.3V voltage stabilization in various electronic applications.

Camera module with Sony IMX219 sensor works with all versions of Raspberry Pi. The camera is equipped with a matrix with a resolution of 8 MPx, the maximum video resolution is 1080p. ArduCAM B0103

The Tic T834 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC).

The Step-Down converter module on the XL7015 chip converts the voltage in the range of 5-80V to 5-20V, with a maximum current of 0.8A and a recommended output power of 7W. It has protection against overheating, short circuit and current overload, and its board size is 16 x 44 mm.

The Step-Down converter module on the MP1584EN chip converts the input voltage (9-35V) to the regulated output voltage (0.8-25V) with a maximum current of 5A and a power of 25W. It operates in temperatures from -20°C to 75°C and has a compact size of 45 x 31 x 16 mm.

Laser sensor of air pollution with particles PM1,0, PM2.5 and PM10. It allows for precise analysis of the amount of pollutants in the environment, has small dimensions and a built-in silent transfer fan. Data is output to the UART interface. Planter PMSA003-C

GPS-14414

SEN-14347

SEN-14351

The Step-Up Converter Module converts input voltage (8.5-50V) and input current (up to 15A) to output voltage (10-60V) and output current (up to 12A) with high conversion efficiency (96%) and overvoltage protection high intensity. The module can operate in a wide temperature range (-40 - 85°C) and frequency (150kHz), allowing constant current adjustment from 0.2 to 12A.

PmodCMPS2 is a module with a digital magnetometer based on the Memsic MMC34160PJ system. It has a resolution of 0.5 mG (within ± 16) and accuracy up to 1 °. For communication with the module, an I2C interface is provided on the 6-pin Pmod connector. Digilent 410-355

Module with a voltage divider. Equipped with a Grove connector, it allows the input voltage to be reduced by 3 or 10 times. Seeed Studio 104020000

ArduCam CSI to HDMI modules are designed to work with cameras: Raspberry Pi V1 and Raspberry Camera V2. ArduCAM CSI to HDMI allows you to extend the signal from cameras using the HDMI <-> HDMI cable (up to 10 meters). Arducam B0091