Category: Electronic modules

The UX-52 panel brush motor speed controller is a versatile device with speed adjustment from 90 to 1400 rpm. It offers precise control of motors with an input voltage of 220VAC, featuring a solid construction and a convenient digital display.

Module with the PAM8904 controller designed specifically to control piezoelectric elements. The amplifier operates over a wide frequency range, up to 300 kHz, and allows for gain up to approximately 13 Vpp. Adafruit 5791

Step-Down DC-DC converter module based on the D36V6F12 system. Input voltage 12.2.50V, output voltage 12V (max. 600mA). Pololu 3796

The converter module converts the voltage in the range of 3-7.2V to 200KV with an efficiency of over 90%. It is compact with dimensions of 24 x 64 mm and operates in temperatures from -40°C to 85°C.

MEMS MSM261S4030H0 microphone module designed to work with Sipeed MAix kits. The module is characterized by high sensitivity, low noise and low cost. Seeed Studio 107990153

MP3 panel with LCD display for installation in the audio device. It allows you to play files in MP3, WAV and WMA format from USB memory, SD card, via AUX and Bluetooth 5.0. Has a built-in FM receiver. modBluAud

Gravity module designed based on the GP8501 system. It is a two-channel DAC (analog-to-digital) converter with PWM communication that offers an output signal with 8-bit resolution and 0.5% accuracy. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1037

Module with real time clock (RTC) PCF85063TP and CR1225 battery socket. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 102020083

Two-channel driver of direct current (DC) motors with an operating voltage from 5 to 30 V and a maximum continuous current of 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MDD10A

Module with a button and blue LED backlight. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020046

Module with a bidirectional converter for the I2C bus, based on the PCA9306 system. It allows you to connect two I2C modules operating with different voltage levels. SparkFun BOB-15439

Module with EEPROM memory, capacity 512 kbit (64kB). Communication takes place via the I2C interface. The module has 3 jumpers that enable selection of one of 8 addresses. SparkFun SPX-14764

A compact stepper motor controller with a TMC2225 system with an operating voltage from 4.75 to 36 V. It offers smooth, quiet operation, high efficiency, various operating modes and easy configuration. It is controlled via a STEP/DIR or UART interface and is an ideal solution for 3D printers and similar applications

Range finder with a measuring range up to 12m. The current consumption is up to 120mA and the supply voltage 4.5 ... 6V. Communication via the UART interface. DFRobot SEN0259

Shunt regulator with a fixed voltage of 26.4V, bypass resistance of 2.8 Ohms and a total of 32 SMT bypass resistors on both sides of the PCB with the possibility of adding an external potentiometer to adjust the preset voltage. Pololu 3775

USB - RS232 adapter equipped with a USB type A connector and an RS232 connector in the DB9 male standard. It uses the original FTDI FT232RL chip, which guarantees a reliable connection between a variety of devices. Waveshare USB-TO-RS232-Male-Cable

Ultrasonic distance sensor MB1020 with a range from 0 to 645 cm. It has an output in the form of a serial interface, analog signal or generates an impulse whose duration is proportional to the measured distance. Pololu 792

TB6612FNG Dual Motor Driver Carrier

The Step-Up converter module converts the voltage in the range of 10-60V to 12-90V with an efficiency of 97% and operates in the temperature range of -20°C to 65°C. The maximum current is 40A at the input and 22A at the output, with a weight of 400g.