Single-channel brushed DC motor driver based on the MPQ6612A chip, enabling bidirectional motor control with a supply voltage of 4-40 V and up to 4 A continuous current. The module offers motor current sensing, active current limiting, overcurrent and thermal protection, and supports PWM control up to 200 kHz. The carrier board includes factory-soldered connectors, allowing the module to be used without additional soldering. Pololu 5286

The board based on the L298 Dual Full-Bridge Motor Driver; can provide up to 4 Amps of current to the motors (2 Amps per motor). ROB-09571

2-channel brush motor controller module with PWM signal mixing function. It allows you to control two DC motors with a current consumption of up to 5 A per channel

This compact breakout board is for ROHM’s BD65496MUV motor driver, which offers an operating voltage range of 2 V to 16 V and can deliver a continuous 1.2 A to a single brushed DC motor. Pololu 2960

Module with 2-channel driver for DC motors L298P. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 105020093

DRV8801 Single Brushed DC Motor Driver Carrier

FeatherWing expansion board for controlling DC motors, stepper motors, and servo motors, based on the PCA9685 PWM controller and TB6612FNG H-bridge drivers. Adafruit 3243

Dual MAX14870 Motor Driver is a dual DC motor controller compatible with the Arduino standard that allows you to control two DC motors with 4.5 ... 36V continuous current of 1.7A. Polol 2519

A powerful controller designed to drive a single brushed DC motor with an encoder in the Pimoroni Yukon system. It offers up to 8 A continuous and 12 A peak current at a supply voltage of 5 to 17 V, making it suitable for demanding robotic projects. The module provides precise control thanks to encoder support and built-in current, temperature, and error sensors. Pimoroni PIM691

ual MAX14870 Motor Driver is a dual DC motor driver compatible with the Raspberry Pi standard that allows you to control two DC motors with 4.5 ... 36V continuous current of 1.7A. Pololu 3758

Single-channel DC motor driver with an operating voltage from 10 to 45 V and a continuous current up to 40 A. It can be controlled by an analog signal, PWM, UART, RC or by means of built-in buttons. Cytron MDS40B

Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 1.2 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-3AMOTOR

Compact module for driving two DC motors, 6.5–37 V, continuous current 12 A per channel, peak 70 A, with protections and status indicators. DFRobot DFR0601

DC motor driver based on the Texas Instruments DRV8263H-Q1. It can control one DC motor in two directions or two motors in one direction from a supply voltage of 4.5-65V and a continuous current of up to 3.5A (limited to 10A). The module offers three control modes: Phase/Enable (PH/EN), PWM (IN/IN), and independent half-bridges. Built-in current sensors and protection features protect against overload, overheating, and reverse power connection. The 3-5V logic control is decoupled from the motor supply, increasing safety and integration flexibility. Pololu 5238

The controller enables to supply the motors with voltage in the range of 10-47V and power consumption in continuous operation of 1.7A (4.5A peak) for each channel in dual or 3.4A mode (9A peak) in single channel mode. Pololu 2999

The expansion module is designed to work with micro:bit. It allows you to control 4 DC motors or two stepper motors and 8 servos. It communicates via the I2C interface. DFRobot DFR0548

Pololu High-Power Motor Driver 36v20 CS

Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-MDD10

This controller allows independent control of three DC motors using a single I²C bus. It supports motor supply voltages ranging from 4.5 to 44 V and currents up to 0.8 A continuous per channel, making it suitable for a wide range of robotic and mobile applications. I²C communication eliminates the need to generate PWM signals and significantly saves microcontroller pins. The ability to connect multiple controllers on a single bus allows for easy scaling of the system to larger motor counts. Pololu 5085

This controller allows independent control of three DC motors using a single I²C bus. It supports motor supply voltages ranging from 4.5 to 44 V and currents up to 0.8 A continuous per channel, making it suitable for a wide range of robotic and mobile applications. I²C communication eliminates the need to generate PWM signals and significantly saves microcontroller pins. The ability to connect multiple controllers on a single bus allows for easy scaling of the system to larger motor counts. Pololu 5084