Category: Electronic modules

Audio player and recorder with built-in VS1003 codec, 3.5 mm jack audio output and a microphone

2-channel stereo audio mixer in a metal housing. It has four outputs, on which the summed signal from 2 inputs is available. It is powered with the voltage from 5 to 19 V

Module with DC motor driver DRV8876. It can work with motors supplied with the voltage from 4.5 to 37 V and current consumption up to 1.1 A. Pololu 4037

Camera module with MT9D111 matrix with a resolution of 2 MPx and size 1 / 3.2 ". The transmission speed in JPEG format at full resolution of 1600 x 1200 pixels is 15 fps. It is equipped with a CS mount lens with parameters: 3MP, 1: 1.4, focal length 4.0 mm , format 1 / 2.5 \'\'. The device works with 3.3 V, it communicates via a parallel interface. ArduCam B0009

DAC converter module with current output in the range of 0 to 25 mA. It is powered by 18 V to 24 V and communicates via I2C interface (Gravity connector). It is used as a controller in industrial applications. DFRobot DFR0972

Camera module with an OV5642 matrix with a resolution of 5 MPx and a size of 1/4 "with output in JPEG format. The transmission speed in the full resolution of 2592 x 1944 pixels is 15 fps. It is equipped with an M12x0.5 1/4 \'\' lens. The device works with 3.3 V, it communicates via a parallel interface. ArduCam B0020

Bluetooth audio receiver module with microphone in set with 3.5 mm Jack adapter. It enables wireless transmission of sounds. It is equipped with a 3.5 mm audio jack, microUSB socket and a control button

Great way to upgrade a project that uses a photocell and needs RoHS compliance. Due to the high rejection ratio of infrared radiation, the spectral response of the ambient light sensor is close to that of human eyes. Adafruit 2748

50 W audio signal converter that reduces the speaker signal from the player to the level of RCA inputs. It allows you to connect the radio to an external power amplifier. Fwaeh FH-103

The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. The power pin provides the 5V @ 500mA direct from the USB port and the RX/TX pins are 3.3V level for interfacing with the most common 3.3V logic level chipsets. Adafruit 954

The analog pH meter, specially designed for Arduino controllers, with the connector (Gravity series). It has an LED which works as the Power Indicator, a BNC connector and PH2.0 sensor interface. The pH measurements at ± 0.1pH (25?). SEN0161

BMS module for two 7.4V lithium cells. Charging, discharging and over-discharge protection. The cells can be charged with a continuous current of up to 20 A

Step-Up DC-DC converter module. It has an input voltage of 1.3 to 16 V, an output voltage of 15 V and a maximum input of up to 2 A. Pololu 4946

A module with a two-channel DC motor driver based on the TB6612FNG system. Designed for Wemos D1 Mini

The Step-Up NCP1402 Buck Voltage Regulator module with output  voltage 3.3V, input voltage range of 0.8-3.3V and a maximum output current of 200 mA. Pololu 2114

Module with RGB diode and P9813 controller. It is powered with the voltage of 5 V and controlled by the I2C interface (Grove). Seeed Studio 104030006

Audio module with DAC, stereo amplifier and display, designed to work with the Raspberry Pi. Pimoroni PIM484

Module with a 12 V relay and a timer. It enables the implementation of delayed switching on or off of the circuit with the possibility of time adjustment

Gravity: Digital 10A Relay Module is a module with 10A 35VAC / 30VDC relay compatible with devices with control signals in the range of 2.8 ... 5.5V. DFRobot DFR0473

Module with the driver of motors TB6612FNG and driver PWM PCA9685 for Raspberry Pi Pico. It allows you to control the movement of 4 DC motors. Waveshare Pico-Motor-Driver