OP1000-3 - 1000X tip for SigOFIT Micsig 350MHz probe
ID: 1197267
5902186321168
zł1,398.90
Tax included
zł1,137.32 tax excl.
A 1000X attenuation factor probe tip. Designed for Micsig SigOFIT series probes operating in the 100MHz, 200MHz and 350MHz frequency bands. Micsig OP1000-3
Description
The 1000X attenuation probe tip is designed to extend the measurement range of Micsig high-frequency probes. It enables operation at high voltages while ensuring safety and measurement accuracy. Thanks to its low input impedance, it minimizes interference with the tested signal. Fully compatible with OIP350 probes, this tip is suitable for signal analysis up to 100MHz, 200MHz, and 350MHz, both in laboratories and in the field. Its compact design facilitates access to hard-to-reach measurement points.
Features
- Attenuation ratio: 1000:1 @0dB ±1250V, 100:1 @20dB ±125V
- Maximum operating voltage: ± 25000Vpp
- Input impedance: 20.94MΩ || 1pF
- Compatible with OIP350 probes
- Adapter type: MCX
1197267
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Insulated fibre-optic probe with a measurement range of up to 2500 V. Operates up to 350 MHz and can be connected to an oscilloscope via a BNC connector. Battery-powered. Micsig OIP350B
Delivery date unknown
No product available!
Other products in the same category (16)
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-1.0mm
zł47.90
24h
Available quantity: 1
Available
Cable (adapter) of a BNC connector to banana plugs. Allows convenient connection of the device to an oscilloscope, for example. Hantek HT30A
zł35.46
4 weeks
No product available!
Cable (adapter) of a BNC connector to banana plugs. Allows convenient connection of a device to an oscilloscope, for example. BNC Q9
zł11.38
24h
Available quantity: 4
Available
Probe for measuring direct current up to 800 A and alternating current up to 500 A. Operates at 5 kHz and can be connected to an oscilloscope via a BNC connector. Powered via USB. Hantek CC-800
zł625.10
24h
Available quantity: 2
Available
High-voltage differential probe. It has good measurement characteristics: a bandwidth of 50 MHz and an operating voltage of up to 1300 V. The probe has two attenuation coefficients: 50X and 500X. Hantek HT8050
zł938.99
4 weeks
No product available!
High-voltage differential probe. It has good measurement characteristics: a bandwidth of 100 MHz and an operating voltage of up to 1300 V. The probe has two attenuation coefficients: 50X and 500X. Hantek HT8100
zł1,349.01
4 weeks
No product available!
Universal oscilloscope probe with BNC connector and 10:1 voltage divider. It has a frequency response of 80 MHz and allows measurements with a maximum voltage of up to 600 V. Hantek PP-90
zł40.00
24h
Available quantity: 16
Available
A set of needle probes used for piercing wire insulation. They can be used as pin probes when working with small PCBs or connectors. Hantek HT307
zł33.12
4 weeks
No product available!
Universal oscilloscope probe with BNC plug and 10:1 voltage divider. It has a frequency range of 60 MHz and allows you to perform measurements with a maximum voltage of up to 600 V.
zł47.75
24h
Available quantity: 2
Available
Oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Hantek HT25COP
zł440.00
4 weeks
No product available!
Oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Hantek HT20COP
zł237.49
4 weeks
No product available!
An oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Micsig MS-A-008
zł142.45
4 weeks
No product available!
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 100 MHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. MOIP100P
zł12,099.01
4 weeks
No product available!
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 200 MHz, it can be connected to the oscilloscope via the BNC connector. Micsig MOIP200P
zł18,018.44
4 weeks
No product available!
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 350 MHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. Micsig MOIP350P
zł49,999.00
4 weeks
No product available!
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 500 MHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. Micsig MOIP500P
zł74,999.00
4 weeks
No product available!
A 1000X attenuation factor probe tip. Designed for Micsig SigOFIT series probes operating in the 100MHz, 200MHz and 350MHz frequency bands. Micsig OP1000-3