Terasic HDMI-FMC is a HDMI transmitter/receiver daughter board with FMC (FPGA Mezzanine card) interface

Recorder v3.0 is a module that allows you to record and play sounds. The module was based on the ISD9160FI system, it also has a FLASH memory with a capacity of 2 MB, which allows for recording up to 83 seconds long. The set contains a small loudspeaker on which recorded sounds can be played. Seeed studio 107020029

Gravity module with a colored RGB WS2812 LED. Thanks to the controller built into the diode, you can connect the modules in series and control all with one microcontroller port. DFRobot DFR0605

Analogue temperature and humidity sensor module based on SHT30 sensor. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers, such as Arduino, micro:bit, ESP32. DFRobot DFR0588

Set (5 pieces) of wires for attaching modeling servos with the Grove system. With one wire you can connect 2 servos to one Grove slot. Seeed studio 110990057

Optical Time of Flight sensor with Pmod I2C connector. The built-in ISL29501 digital signal processor calculates the time it takes for the light emitted by ToF to reach the destination and back. The calculated time is proportional to the distance. Pmod ToF has a range of up to 5 m. Digilent 410-392

GPS Receiver, Digilent, RoHS

Heart rate monitor module based on the popular MAX30101 chip. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-16474

GPS module with 72-channel GNSS NEO-M8U receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. Built-in accelerometer and gyroscope. SparkFun GPS-16329

Module with a button and green LED backlight. Controlled by the I2C interface, it has a built-in debouncing mechanism, pull-up resistors as well as interrupts and a FIFO queue. SparkFun BOB-16842

Module with Grove connector equipped with AS5600 magnetic encoder with a resolution of 12-bit. It allows for non-contact measurement of the angle of rotation. The module has an analog/PWM output and an I2C interface. Seeed Studio 101020692

Miniature pressure measurement module equipped with a 25 psi piezoresistive pressure sensor. It allows you to perform calibrated and compensated pressure measurements from 60 mbar to 2.5 bar. SparkFun SEN-16476

Module with MOSFET and a Gravity connector. It allows you to easily connect and control the voltage from 5V to 30V and the current up to 2.5A. DFRobot DFR0643

Starter kit with Qwiic modules designed to work with the Raspberry Pi. The set consists of an overlay for Raspberry Pi with a standard 40-pin connector and four Qwiic connectors, OLED display, VCNL4040 distance sensor and environmental sensors. SparkFun KIT-16841

Data logger pre-programmed to automatically record data from IMU, GPS and Qwiic series sensors. SparkFun DEV-16832

Expansion board for micro:bit modules with connectors compatible with Boson and Gravity sets. DFRobot DFR0521

Module with an analog joystick that returns the X and Y position and the pressed state. The module has an ATtiny85 microcontroller on the board, which processes analog data of the joystick and sends it via the I2C interface. SparkFun COM-15168

Professional pH measurement set with an industrial silver chloride electrode (Ag/AgCl), the measurement in the range from 0 to 14 pH is converted into voltage with a linear characteristic. DFRobot SEN0169-V2

TerasIC DVI-HSMC is an FPGA expansion card with a DVI transmitter and receiver, enabling support for high-resolution video signals in multimedia projects and image processing systems. With compatibility with Terasic and Altera platforms, it offers rapid deployment and testing of visual applications based on FPGA devices.