Category: Electronic modules

2x1.2A DC Motor Driver is a dual controller of DC motors powered with 2.5 ... 12V voltage with a maximum current consumption of 1.2A (3.2A peak) per channel. DFRobot DRI0044

The S9V11F3S5C3 switching step-up/step-down regulator efficiently produces a fixed 3.3 V (default) or 5 V (selectable) output whether it is higher or lower than the input voltage, which can range from 3 V to 16 V. The regulator also has fixed 3.3 V low-voltage cutoff with hysteresis that can be used to prevent battery over-discharge.

Module with an AB class amplifier based on the Boomer® LM4853 system. It can work in two modes: mono (power 1.5 W, load 4 Ω) or stereo (power 300 mW, load 8 Ω). It has a potentiometer for power control and gain control for the left and right channel. SparkFun DEV-14475

The X-NUCLEO-IHM16M1 motor driver expansion board is based on the STSPIN830 monolithic driver for three-phase brushless motors. It represents an affordable, easy-to-use solution for driving brushless motors in your STM32 Nucleo project, implementing single and three-shunt current sensing

(DRI0009) 2A Motor Shield For Arduino

QTR-1A Reflectance Sensor (2-Pack)

DC-DC Step-up converter module based on the U3V70F12 system. Input voltage 2.9-12V, output voltage 12V, maximum current 10A. Two mounting holes. Pololu 2895

DC-DC Step-up converter module based on the U3V70F5 system. Input voltage 2.9 ... 5V, output voltage 5V, maximum current 10A. Two mounting holes. Polol 2891

The board generates 16 PWM signals and communicates using the digital I2C interface, it has a built-in PCA9685 chip. MOD 71

Module with 1 QTR type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 30 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4201

Module with 1 QTRX type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 30 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4441

Module with 6 QTRX type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 40 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4406

The Step-Down D24V6F5 Buck Voltage Regulator module gives the output voltage of 5V with a wide input voltage range of 7-42V and a maximum output current of 600 mA. Pololu 2107

The compact (0.4″ × 0.5″) D24V5F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 5 V while allowing for a maximum output current of 500 mA. Pololu 2843

The compact (0.4″ × 0.5″) D24V5F12 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 12 V while allowing for a maximum output current of 500 mA.

Module with 4-channel ADC ADS1115 converter. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 1085

Laser sensor of air pollution with PM2,5 and PM10 particles. It allows for precise analysis of the amount of pollutants in the environment, has small dimensions and a built-in silent transfer fan. The data is output to the UART interface and via the PWM signal. Nova Fitness SDS018

The Step-Up Buck Voltage Regulator module with adjustable output voltage in range of 4-25V with a input voltage range of 1.5-16V and a maximum output current of 2A. Pololu 799

Module with rotary potentiometer. The connector in this module has been moved to the other side of the PCB, which makes it easier to assemble and use this module. The module has a connector in accordance with the Grove standard. Seeed studio 101020048

Single-channel DC motor driver that can control the movement of the drive with a supply voltage of up to 36 V and a current consumption of up to 15 A. Controlled by a PWM signal. DFRobot DRI0042